Waltron AQUALERT Aqualyzer 3051 Скачать руководство пользователя | Manualshive

Страница: 70 / 70

background image

Appendix C

– Multiple Stream Sequencer

69

Waltron User Manual

3051 Hardness Analyzer

Pressing RUN, the following page will be displayed:

Figure C.7: Multistream sequencer RUN Menu of the user interface.

START ON-LINE:

This button puts the analyzer to online operation. The analyzer will perform a continuous cyclic analysis
with the sequence CH1, CH2, CH3, CH4 of the active channels selected. This condition is identified as
online and ONLINE is displayed on the button. Pressing the button again will cause the analyzer to finish
the cycle in process and put the analyzer in stand-by mode.

SINGLE:

This command allows the user to perform an analysis cycle on the active channel. At the end of the cycle,
the analyzer will go into stand-by mode and wait for the user’s next command.

EXTRA:

This command will perform a cycle based on the programming of the extra cycle. The default
programming for the extra cycle is set to a CALIBRATION cycle.

EMERGENCY STOP:

This command will immediately stop the analyzer at the current step of the analysis in progress.  The
analyzer will go into the MANUAL STOP condition.  On the main screen appear the message “manual
stop” red coloured and the FAULT alarm contact  will be activated.  To restart the analyzer after an
emergency stop, it is necessary to reset the fault by pressing the yellow colored RESET EM. STOP. This
will force the analyzer to stand-by conditions.

«
...
68
69
70

Содержание AQUALERT Aqualyzer 3051







































































Отзывы:

Нет отзывов

Похожие инструкции для AQUALERT Aqualyzer 3051

Бренд: Lambrecht Страницы: 5

Бренд: Keithley Страницы: 25

Бренд: Van Walt Страницы: 12

Бренд: Sensia Страницы: 16

Бренд: Ecolab Страницы: 95

WALLACE & TIERNAN P7 ADVANCED

Бренд: Evoqua Страницы: 98

DIRIS Digiware D-40

Бренд: socomec Страницы: 58

Бренд: Hanna Instruments Страницы: 28

Бренд: Omega Страницы: 15

Бренд: TASKING Страницы: 12

Бренд: PCB Piezotronics Страницы: 14

Бренд: ZIEHL Страницы: 37

Бренд: XPOtool Страницы: 6

Бренд: Simex Страницы: 48

HP Fire Service

Бренд: Neptune Technology Страницы: 14

Бренд: KATA Страницы: 20

Бренд: Polhemus Страницы: 2

Бренд: MEWOI Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды