Waltron AQUALERT Aqualyzer 3051 Скачать руководство пользователя | Manualshive

Страница: 43 / 70

background image

Operation

42

Waltron User Manual
3051 Hardness Analyzer

6.5

ONLINE MEASUREMENT

In online mode, the analyzer will run perform consecutive analysis cycles until it is manually
stopped or the out of sample alarm is tripped.

NOTE:

When starting the analyzer for the first time or restarting it
from any period of shutdown, do not proceed to put the
analyzer into online operation until a calibration has been
performed.

1.

Connect the sample tubing to the fast-loop reservoir and turn on sample flow to the fast
loop reservoir.

2.

Check that the sample fills the fast loop reservoir so that the float switch rises and sample
is being discharged from the overflow drain.

3.

Put the analyzer into online measurement mode by pressing the RUN Menu and selecting
START ON LINE.



The absorbance detected by the analyzer is used along with the blank and
calibration values to determine a concentration in ppb.

4.

When the analyzer has finished the analysis cycle, the concentration reading will be
displayed on the main screen. The new result and previous results are stored in the data
logger (up to 500 measurement results).

5.

The analyzer will wait the user defined amount of time (see Section 5.7.1) and then
proceed to run additional analysis cycles.

6.

To bring the analyzer out of online operation, press the RUN Menu. The top box where
START ONLINE was previously, will now be blank and dark gray. Pressing this box
will tell the analyzer to complete the current analysis cycle and go into stand-by mode at
its completion.

6.6

GRAB SAMPLE

The grab sample feature allows the user to measure the concentration of an external sample.

NOTE:

When starting the analyzer for the first time or restarting it
from any period of shutdown, do not proceed to run a grab
sample analysis until a calibration has been performed.

1.

If the analyzer is in online operation, it is necessary to put it into standby mode.



Press the RUN Menu and select the START ON LINE button (blank, dark gray box
on the top of the RUN Menu).



The analyzer will finish the analysis cycle that is currently in progress and go into
standby mode.

2.

Turn off sample flow to the fast loop reservoir.

3.

Disconnect the sample tubing from the fast-loop reservoir and connect it to the grab
sample source.



The grab sample source should have at least 200 ml of sample present.

4.

Perform an analysis cycle by pressing the RUN Menu and selecting CH 1.

«
...
41
42
43
44
45
...
»

Содержание AQUALERT Aqualyzer 3051







































































Отзывы:

Нет отзывов

Похожие инструкции для AQUALERT Aqualyzer 3051

Бренд: Larson Davis Страницы: 193

Бренд: Facom Страницы: 116

Бренд: Bacharach Страницы: 64

Charge Analyzer 711

Бренд: 3M Страницы: 24

Бренд: Accurate Logic Страницы: 50

Acuvim-L Series

Бренд: AccuEnergy Страницы: 188

Бренд: VAMP Страницы: 78

Бренд: Callaway Страницы: 11

Бренд: Rayjet Страницы: 81

Бренд: Laserworld Страницы: 4

Бренд: Laserworld Страницы: 4

Бренд: Laserworld Страницы: 4

Бренд: LaserLiner Страницы: 56

Бренд: Lasermet Страницы: 8

Бренд: Lake Shore Cryotronics Страницы: 97

Бренд: Dräger Страницы: 538

Бренд: Dakota Digital Страницы: 38

Бренд: Swema Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды