WALTHER PILOT Pilot III F, Руководство по эксплуатации

Страница: 19 / 53

36 37
Clean the spray gun
• before each change of spraying material
• at least once a week or
• several times a week if required by the spraying medium and depending on the
degree of fouling.
Complete Cleaning
1. Disassemble the spray gun.
2. Clean the air cap and the material nozzle with a soft brush and cleaning fluid.
3. Clean all other components and the gun body with a soft cloth and cleaning fluid.
4. Coat the following parts with a thin layer of grease:
• needle spring
• all sliding parts and bearing points.
The moving internal parts must be greased at least once a week.
The springs should always be coated with a thin layer of grease. For this, always use
a non-acidic, non-resinogenic grease and a soft brush.
Assemble the gun again in reverse order.
Attention
Do not use any hard, sharp or pointed objects when cleaning the spray gun.
WALTHER is not responsible for any damage resulting from improper cleaning.
10 Waste Disposal
Waste spraying media and waste material from cleaning and servicing must be dis-
posed of in accordance with all applicable local and national regulations.
Warning
Observe the instructions issued by the manufacturers of the spraying and cleaning
material at all times. The improper disposal of waste material endangers the health
of human beings and animals!
11 Technical Data
PILOT III F
Net weight 590 g Pressure ranges:
Max. input air pressure
Max. material pressure
8 bar
8 bar
Air cap*
High-Pressure Air
Cap
Nozzle sizes optional:
• 0,5 • 0,8 • 1,0 • 1,2 • 1,5 • 1,8 • 2,0
• 2,5 • 3,0 • 3,5 mm ø
Max. operating tem-
perature
43 °C
Noise level
(measured at approx.1 m
from the spray gun)
85 dB (A)
*Other air caps available on request.
PILOT III F-MP
Net weight 590 g Pressure ranges:
Max. input air pressure
Max. spraying air pressure
Max. material pressure
3,3 bar
1,4 bar
8 bar
Air cap Medium-
Pressure Air
Cap
Nozzle sizes optional:
• 0,5 • 0,8 • 1,0 • 1,2 • 1,5 • 1,8 • 2,0
• 2,5 mm ø
Max. operating tem-
perature
43 °C Noise level
(measured at approx.1 m
from the spray gun)
83 dB (A)
PILOT III K
Net weight 590 g Pressure ranges:
Max. input air pressure
Max. material pressure
8 bar
8 bar
Air cap High-Pressure
Air Cap
Nozzle sizes optional:
1,0 • 1,5 mm ø
Max. operating tem-
perature
43 °C Noise level
(measured at approx.1 m
from the spray gun)
85 dB (A)
Air consumption:
Atomising
air
pressure
PILOT III F
4-hole-air cap
PILOT III F-MP
Medium-pressure
air cap
PILOT III K
High-pressure air cap
Round
jet
Flat
jet
Round
jet
Flat
jet
Round
jet
Flat
jet
1 bar 160 l/min 260 l/min 140 l/min 190 l/min 200 l/min 270 l/min
2 bar 220 l/min 320 l/min 190 l/min 270 l/min 275 l/min 380 l/min
3 bar 290 l/min 370 l/min 230 l/min 330 l/min 325 l/min 450 l/min
4 bar 300 l/min 410 l/min 260 l/min 390 l/min 375 l/min 525 l/min
5 bar 320 l/min 450 l/min 290 l/min 405 l/min 400 l/min 575 l/min
6 bar 380 l/min 490 l/min 300 l/min 425 l/min 450 l/min 625 l/min
Right to effect technical changes reserved.