background image

S-Cape

 2MR Hand Control Operation Guide 99300906

The three step procedure below is required to program 2 hand controls to operate 1 bed.
Before beginning, make certain the bed is plugged into a working grounded electrical outlet.

If programming fails, initiate the programming procedure a second time.

S-CAPE

 2MR PROGRAMMING  

2 hand controls - 1 bed

POS 1

BUTTON

TRANSMISSION
INDICATOR
LIGHT

FIGURE 3

HEAD MASSAGE

ON/OFF

BUTTON

STEP 1

The bed will be equipped with either a

power down box

 or 

J box

 receiver unit

(

FIGURE 2

). Locate the receiver unit for the

bed and press the 

learn button

 for 1 second

and release. 

Note: If you experience

difficulty locating or reaching the learn
button on a J box equipped adjustable bed,
refer to

 J Box Programming

 on page 5.

STEP 2

On hand control 1, simultaneously press
and hold the 

POS 1 

and the 

head massage

on/off buttons

 (

FIGURE 3

). 

The

transmission indicator light will 

flash

slowly

 and then 

flash rapidly

 to indicate

programming mode.

 Continue to hold for 5

seconds and then release the buttons.

HAND

CONTROL 1

HAND

CONTROL 2

STEP 3

Repeat Step 1 and Step 2 with hand control
2.

Two hand controls are now programmed to
operate one bed.

J BOX

FIGURE 2: Power down box and J box receiver units.

LEARN
BUTTON

LEARN
BUTTON

POWER
DOWN BOX

POWER DOWN
BOX RECEIVER
UNIT IS NOT
MOUNTED TO
BED FRAME.

J BOX RECEIVER
UNIT IS MOUNTED
TO THE BOTTOM
SIDE OF THE
BED FRAME.

7

NOTE

OPERATE ONLY ONE (1) HAND CONTROL AT A
TIME. OPERATING TWO (2) HAND CONTROLS
AT THE SAME TIME WILL MOMENTARILY
BLOCK BOTH RF SIGNALS AND PREVENT BOTH
CONTROLS FROM FUNCTIONING.

Содержание S-cape 2MR













Отзывы: