Wallenstein WX350 Скачать руководство пользователя

Страница: 26 / 32

Troubleshooting

WX350, WX360

3-point Hitch Wood Splitter

9. Troubleshooting

The following table lists some problems that may be

encountered, with possible causes and solutions.

If a problem persists after reading through the

Troubleshooting section, contact the local dealer,

distributor or Wallenstein Equipment. Have the

machine serial number ready.

Problem

Cause

Solution

Cylinder rod moves slowly or

does not move. Screeching or

hissing noise.

No hydraulic oil pressure.

Oil filter plugged. Change filter.
Low hydraulic oil level. Add oil.
System relief pressure setting too low.

Call technician.

Wood jammed around wedge.

Shut machine off and safely remove

wood.

Low engine speed.

Check throttle is setting.

Control handle does not go

to neutral after rod is fully

retracted.

Valve detent set too tight.

Valve detent adjustment required. Call

technician.

Hydraulic oil too cold.

Allow machine to warm up.

Hydraulic fluid is contaminated.

Change hydraulic fluid and filter.

Control handle goes to neutral

before rod is fully retracted.

Detent set too loose.

Valve detent adjustment required.

Control handle does not go to

neutral when released.

Control may be damaged.

Control may need service or be

replaced. Call technician.

Cylinder stops on contact with

wood.

Second stage on pump not

functioning.

Pump may need to be serviced or

replaced. Call technician.

Wedge or push block jumps.

Wedge or push block frame

jamming.

Lubricate slider wear plates.

Leaking hydraulic hose.

Hose loose, worn or damaged.

Tighten or replace hose.

Leaking cylinder.

Seals worn.

Seal replacement may be required.

Call technician.

Cylinder rod moves in wrong

direction.

Hydraulic hoses hooked-up

incorrectly.

Reverse hose connections.

Hydraulic system behaves

erratically.

Incorrect control valve.

Check whether tractor hydraulic

system is open-center or closed.

Match control valve accordingly.

Содержание WX350

































Результаты поиска

Содержание WX350

Отзывы:

Похожие инструкции для WX350

Бренды по названию

Популярные бренды

Wallenstein WX350, Руководство оператора

Результаты поиска

Содержание WX350

Отзывы:

Похожие инструкции для WX350

Бренды по названию

Популярные бренды