Wallenstein BX52RI Скачать руководство пользователя страница 58

Страница: 58 / 72

Service and Maintenance

BX52R, BX72R, BX102R

3 PH Roller-feed Chipper

Checking

Open the upper rotor housing.

CAUTION!

Risk of getting hands pinched or wedged

between lower rotor housing and rotor. Turn

rotor slowly and be aware of hand positioning.

W032

Turn the rotor by hand so that one rotor blade edge is next
to the ledger knife.

Slide the end of the ledger gauge down between the rotor
blade and the ledger knife.

00875

Fig. 77 –

Inserting Gauge

Turn the rotor past the ledger knife with the gauge inserted
between them to check clearance. The gauge should be
tight. Check all four knives.

00877

Fig. 78 –

Checking ledger knife clearance

1.  Rotor Blades
2.  Gauge
3.  Ledger Knife

Adjusting

Loosen the jam nuts on the outside of the ledger knife
support (2).

Turn the two adjuster nuts (1) clockwise so the ledger knife
slides firmly up against the gauge inside the rotor housing.
Move both adjusters evenly.

Remove the ledger knife gauge. Tighten the jam nuts.

00879

Fig. 79 –

Adjusting Ledger Knife

Содержание BX52RI









































































Результаты поиска

Содержание BX52RI

Отзывы:

Похожие инструкции для BX52RI

Бренды по названию

Популярные бренды

Wallenstein BX52RI, Руководство оператора

Результаты поиска

Содержание BX52RI

Отзывы:

Похожие инструкции для BX52RI

Бренды по названию

Популярные бренды