background image

13

PROBLÈME

SOLUTION/CAUSE

Display does not light

1. Tether cord not in position.
2. Circuit breaker on front grill tripped. Push circuit breaker in 

until it locks.

3. Plug is disconnected. Make sure plug is firmly pushed into 

AC household wall outlet.

4. Household circuit breaker may be tripped.
5. Treadmill defect. Contact your dealer.

Tread-belt does not stay centered
Treadmill belt hesitates when walked/
run on

The user may be walking while favoring or putting more 
weight on either the left or right foot. If this walking pattern is 
natural, track the belt slightly off-center to the side opposite 
from the belt movement. 

See General Maintenance section 

on Tread-belt Tension

. Adjust as necessary.

Motor is not responsive after 
pressing start

1. If the belt moves, but stops after a short time and the 

display shows “LS”, run calibration or check the speed 
sensor.

2. If you press start and the belt never moves, then the 

display shows LS, contact service.

Treadmill will only achieve approximately 
5 kmph (3 mph) but shows higher speed 
on display

This indicates motor should be receiving power to operate. 
Low AC voltage to treadmill. Do not use an extension cord. If 
an extension cord is required it should be as short as possible 
and heavy duty 16 gauge minimum. Low household voltage. 
Contact an electrician or your dealer. A minimum of 220 volt 
ac is required.

Tread-belt stops quickly/suddenly when 
tether cord is pulled

High belt/deck friction. 

See General Maintenance section 

on lubrication.

Treadmill trips on board 10 amp circuit 

High belt/deck friction. 

See General Maintenance

Computer shuts off when console is 
touched (on a cold day) while walking/
running

Treadmill may not be grounded. Static electricity is “crashing” 
the computer. 

Refer to Grounding Instructions.

House circuit breaker trips, but not the 
treadmill circuit breaker

Need to replace the house breaker with a “High Inrush 
current” type breaker.

SERVICE CHECKLIST - DIAGNOSIS GUIDE

Before contacting your dealer for aid, please review the following information. It may save you both 
time and expense. This list includes common problems that may not be covered under the treadmill’s 
warranty.

Содержание WTB500


















Отзывы: