Waiwela PH-28C DVSN Скачать руководство пользователя

Страница: 33 / 40

Error Code Guide

When an error code is displayed:

Close the hot water faucet, turn off the switch on the
remote control.

Wait for about 5 minutes before turning the switch on
again.

Open the hot water faucet.

If the error code remains shown:

Close the hot water faucet and turn off the switch on the
remote control.

Take the proper action shown below and attempt
operation of the appliance again.

If the error code is still shown:

Turn off the hot water faucet and turn off the switch on
the remote control.

Take note of the error code displayed and contact your
Paloma dealer or distributor for service.

Notice

: If an error code other than those listed below is

displayed, immediately turn off the hot water faucet, take
note of the error code, turn off the switch on the remote
control and contact your Paloma dealer or distributor for
service.

CAUTION: For your safety DO NOT attempt repair of gas piping, remote control, burners, vent connectors or other

safety devices. Refer repairs to qualified service personnel.

CAUTION: Make certain power to water heater is “OFF” before removing protective cover FOR ANY REASON.

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and

dangerous operation. VERIFY PROPER OPERATION AFTER SERVICING.

Error Code

Possible Cause

What To Do

The Gas Shutoff Valve is not opened
completely.

Open the Gas Shutoff Valve
completely.

Gas Service has been interrupted.

LP Gas is running low. (LP models only)

Contact Gas Utility Company.

Fill up LP Gas container or replace
with a new cylinder of LP Gas.

The hot water faucet is not opened enough.

Open the faucet more to secure
enough volume.

(Every 60 seconds you hear

an alarm or when the faucet is

closed, the alarm stops.)

Air intake or vent termination may be
blocked.

The vent pipes on the concentric vent
termination may not be connected properly.

Remove any obstructions on the air
intake or vent termination.

Contact a dealer for service.

If the error code is still displayed after
taking the above steps.

Contact a dealer for service.

Water heater has build up of lime deposits.

Contact a dealer for service.

Содержание PH-28C DVSN









































Результаты поиска

Содержание PH-28C DVSN

Отзывы:

Похожие инструкции для PH-28C DVSN

Бренды по названию

Популярные бренды

Waiwela PH-28C DVSN, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PH-28C DVSN

Отзывы:

Похожие инструкции для PH-28C DVSN

Бренды по названию

Популярные бренды