WAGO 750-404 Скачать руководство пользователя страница 38

Страница: 38 / 50

•

750-404/000-003 [Frequency Counter 0.1 Hz-100 kHz]

Process

Image

WAGO-I/O-SYSTEM

750

I/O

Modules

Input data

Output data

Status byte

Control byte

Frequency value byte 0 (LSB)

Watchdog-time byte 0 (LSB)

Frequency value byte 1

Watchdog-time byte 1 (MSB)

Frequency value byte 2

reserved

Frequency value byte 3 (MSB) D3

reserved

Control byte

B 0

0 0 0

REQ

Set

output

DO 2

Set

output

DO 1

RANGE_

SEL

REQ1

RANGE_

SEL

REQ0

REQ

Request to change the Watchdog time (T

) with valid data.

RANGE_SEL REQ1

Selection of the integration time and the representation of
measured frequency value.

RANGE_SEL REQ0

Selection of the integration time and the representation of
measured frequency value.

This constant must be set to zero.

Status byte

X X

ST_

GATE

ACK

Status

output

DO 2

Status

output

DO 1

RANGE_

SEL

ACK1

RANGE_

SEL

ACK0

ST_GATE

Status of the GATE input (0=enabled, 1=disabled)

ACK

Acknowledgement T

changed.

RANGE_SEL ACK1 Acknowledgment to Range Selection, Frequency values are valid.

RANGE_SEL ACK0 Acknowledgment to Range Selection, Frequency values are valid.

This value is not evaluated.

With the control and status byte the following tasks are possible:

Setting the Method of Measuring, Frequency Range and Representation:

The method of measuring and the representation depends on the
RANGE_SEL REQ bits in the CONTROL byte. Dependent on the adjusted
measuring method also the maximum frequency range changes.
The following table illustrates the different modes.

Содержание 750-404



















































Результаты поиска

Содержание 750-404

Отзывы:

Бренды по названию

Популярные бренды

WAGO 750-404, Руководство пользователя

Результаты поиска

Содержание 750-404

Отзывы:

Бренды по названию

Популярные бренды