WAGNER FINISH CONTROL 5500, Руководство по эксплуатации

Страница: 25 / 128

19
FinishControl 5500
EN
10
BREAKS IN WORK
1. Switch device off with main switch on the basic unit.
2. Insert spray gun into gun mounting on the device.
In using quick-drying or two-component coating
materials, do not fail to rinse unit through with
a suitable cleaning agent during the processing
period.
Important: The application life of the material can
change as a result of heating. Therefore, please
consult the material manufacturer.
11
TRANSPORTATION
1. Coil power cable around the basic unit.
2. Insert spray gun into gun mounting on the device.
3. Disconnect air hose by pressing the two side clips (Fig. 8).
4. Roll up the air hose and tie it up with the fastening strap.
12
TAKING OUT OF OPERATION AND
CLEANING
1. Turn the machine off.
2. Divide the spray gun. Press catch (Fig. 2, A) down slightly.
Twist spray attachment and gun handle towards each
other.
ATTENTION! Electrical contacts in gun
handle. Never hold the gun handle under
water or immerse it into liquids.
Clean the housing only with a moistened
cloth.
3. Unscrew the container.
Empty the remaining coating material into the original
container.
4. Unscrew feed tube with container seal. (Fig. 11)
The enclosed brush set can be used for particularly
effective cleaning of the spray attachment (examples
Fig. 12 and 14).
5. Clean feed tube and suction nozzle in spray attachment
with cleaning brush. (Fig. 12)
6. Clean the ventilating bore. (Fig. 9, 2)
CAUTION! Never clean seals, diaphragm
and nozzle or air holes of the spray gun
with metal objects.
The ventilation hose and diaphragm are
only solvent-resistant to a limited extent.
Do not immerse in solvent, only wipe.
7. Move the air cap (Fig. 13, 1) to the vertical position for easier
removal and lift it off.
8. Unscrew the union nut (fig. 13, 2).
9. Clean the air cap (fig. 14, 1) and nozzle (3) with a brush and
solvent or water.
Take special care when cleaning the interstices on
the needle (Fig. 14, 5)
10. Clean the outside of the spray gun and container with a
cloth soaked in solvent or water. Use the all-purpose brush
for the thread (Fig. 14, 6).
11. Assemble the parts again (see “Assembly”).
12.1 ASSEMBLY
ATTENTION! Follow the steps described
below exactly for assembly. Otherwise
the spray attachment may be damaged.
1. Push nozzle seal onto the needle so that the groove (slot)
points away from the spray attachment. (Fig. 15)
2. Screw the union nut (Fig. 16, 2) onto the gun and tighten
it.
3. Engage the air cap (Fig. 17, 1) with the union nut. Check if
the air cap has properly locked into place on both sides.
4. Place the container seal from below on the feed tube and
slide it over the collar, while turning the container seal
slightly.
5. Screw the feed tube with the container seal into the body
of the gun.
In order to mount the gun more easily apply
lubricating grease (enclosed) liberally to the O-ring
at the spray attachment and to the O-ring of the
plug connection of the air hose (Fig. 18).
13
MAINTENANCE
13.1 AIR FILTER
Attention! Never operate the device with
the air filter soiled or missing, as dirt could
be sucked up and affect the operation of
the device.
The air filter indicator lights up red if the
air filter needs to be changed.
1. Unplug the power plug.
2. Open the cover on the air filter compartment (left and right)
(Fig. 19).
3. Depending on the degree of soiling, clean (blow out) the
air filter (Fig. 19, 1) or replace it.
BREAKS IN WORK/ TRANSPORTATION/
TAKING OUT OF OPERATION AND CLEANING