Charging The Power Dome
AC Charging
Make sure the supplied AC Charging Adapter is to be powered by the correct voltage.
(i.e. 110V AC or 220V AC). Only use the AC charging adapter supplied with this unit.
1. Make sure all Power Dome switches are set to OFF
2. Open the dust cover on the Charging Jack
3. Connect the AC Charging Adapter to the AC outlet
4. Plug the Charging Adapter’s cord into the Power Dome’s Charging Jack
5. The Charging Indicator will light during the charging process
6. Initial AC charge can take up to 34 hours
7. Do not charge for more than 48 hours
8. After charging the battery, disconnect the adapter from the AC outlet first, then from
the charging jack
9. Replace the dust cover on the charging jack
NOTE: The Charging Indicator light indicates charging. Press the Charge Status Button for
the Voltmeter to show battery voltage and charge status.
DC Charging in Your Vehicle or Boat
Only use the DC charging adapter supplied with this unit.
NOTE: The engine must be running while charging the Power Dome.
1. Make sure all Power Dome switches are set to OFF
2. Open the dust cover on the Charging Jack
3. Plug the Charging Adapter’s cord into the Power Dome’s Charging Jack
4. Plug the DC Charging Adapter into an accessory outlet (cigarette lighter)
5. The Charging Indicator will light during the charging process
6. Do not charge more than 14 hours using the DC method
7. After charging the battery, disconnect the adapter from the accessory socket first, then
from the charging jack.
8. Replace the dust cover on the charging jack
DC Power Port
DC Power Ports (accessory sockets) are located under the Pressure Gauge and the Battery
Status Meter (voltmeter). The ports can power a DC load of up to 11 Amps. Overloading the
port will result in “tripping” a self-resetting circuit breaker. Removing the overload automatically
restores power to the DC Power Ports.
1. Uncover the dust cover from the Power Port
2. Insert the 12V DC accessory plug into the Power Port
3. Operate the appliance as you normally would
4. After use, disconnect the accessory plug from the Power Port
5. Replace the Power Port’s dust cover
6. Recharge the Power Dome as soon as convenient
Using The Air Compressor
The Air Compressor Gauge and ON/OFF Switch are located on the front of the Power Dome.
The Compressor Air Hose Compartment is located on the rear of the Power Dome.
CAUTION:
• Never connect or disconnect the nozzle with the compressor operating.
• Before any tire inflation, look for the recommended inflation pressure information on
the sidewall of the tire.
Inflation Procedure
1. Open the Air Hose Compartment door at the rear of the Power Dome and extend the
air hose.
2. Position the Power Dome so that you see the front panel
3. Make sure nozzle lever is positioned UP (away from the nozzle opening)
4. Remove the valve cap from the valve stem
5. Attach the nozzle to the tire’s valve stem
6. Move the nozzle lever down to secure the nozzle to the valve stem
7. Turn compressor switch on to ON position
8. Monitor the pressure gauge while inflating the tire
9. When recommended tire pressure has been reached, turn the Compressor OFF
10. Disconnect hose and replace valve cap
11. Store the hose in the Air Hose Compartment
12. Recharge the Power Dome as soon as convenient
DC To AC Power Inverter
The Power Dome’s inverter can operate most AC appliances or a combination of appliances up
to 200 watts. Operating time is dependant on the AC load (watts) and the current charge of
the Power Dome’s internal battery. Reduced AC loads and a fully charged battery will result in
longer operating time. Be sure to turn off or disconnect any AC appliance not in use.
There is a user-replaceable 25 amp automotive type fuse to the left of the inverter ON/
Power Dome
TM
200 by Wagan Tech
3
www.wagan.com
© 2010 Wagan Corporation.
All Rights Reserved.
Wagan and wagan.com are trademarks used by Wagan Corporation.
User’s Manual—Read before using this equipment
4
