background image

WAFER GSM-HOUSE INTERCOM UNIT 

http://www.waferstar.com 

Acknowledge

: ALARM01 SET TO 61143815 OK 

When the number is seted to 000000,that means delete the number in this position 

(2)

 check which is the number in a place of the alarm phone list:

 

#PWD123456#ALARM01?  

(PC$PHONE)

 

Acknowledge

: ALARM01 IS 61143815 OK 

(3)

 List all numbers in the alarm phone list:

 

#PWD123456#ALARM=ALL?  

(PC$PHONE)

 

Acknowledge

: ALARM IS XXXXX:XXXX:XXXXXXX:0000:0000 

(Will show total five numbers, if no effective number,that will be replaced with 0000 ) 

 

(4) Alarm mode setup 

 

(

PC$PHONE

)

 

There are two alarm input ,you can set at PHONE or SMS 

#PWD123456#ALARM-IN1=ON:PHONE:10,ALARM-IN2=OFF  

PC$

PHONE

 

Acknowledge

: ALARM_IN1=ON:PHONE:10,ALARM_IN2=OFF OKAY 

#PWD123456#ALARM-IN1=ON:SMS:300,ALARM-IN2=ON:PHONE:10  

PC$

PHONE

 

Acknowledge

: ALARM_IN1=ON:SMS:300, ALARM_IN2=ON:PHONE:10 

If at phone mode: when receive the alarm input,then will phone the number in the alarm phone list until you 

reject the phone call or that will continue to phone the number again after the minutes setted. 

If at SMS mode: When receive the alarm input,then will send the SMS to the number in the alarm phone list 

until you send the SMS to PAUSE the alarm . 

 

(5) Config the SMS TEXT :   

(PC)

 

#PWD123456#UDI1:XXXXXX, UDI2:XXXXXX 

Acknowledge

: UDI1:XXXXXX, DI2:XXXXXX OKAY

 

(When the Alarm input is triggered,then will send the   
SMS you already setted with this UDI command) 

Check the text    set 

#PWD123456#UDI?

 

Acknowledge:

   

UDI1:ABC1, UDI2:ABC2 

 
#REPORT 
Report the system status change

   

(PC$PHONE)

 

When setup to: 

#PWD123456#REPORT=ON    

Acknowledge

REPORT SET TO ON 

Then any device status change would send the alarm SMS to Alarm01 number

 

#PWD123456#REPORT=OFF 

Acknowledge

:

 REPORT SET TO OFF 

No report for the device status change 

#PWD123456#REPORT? 

You will receive the SMS reply:

REPORT IS ON

 or 

REPORT IS OFF 

Check the REPORT setting status 

 
#CSQ 
Check GSM signal quality

.  

(PC$PHONE)

 

This command is useful to see what is the GSM network 

Содержание GSM-HOUSE














Отзывы: