Wacker Neuson GPS 8500 страница 9 Скачать руководство пользователя | Manualshive

Страница: 9 / 60

background image

GPS 8500/GPS 9700

Safety Information

wc_si000252gb.fm

9

1.2.11 ALWAYS transport the generator in an upright position.
1.2.12 ALWAYS keep the machine at least one meter (three feet) away from

structures, buildings, and other equipment during use.

1.2.13 ALWAYS keep the area immediately surrounding and underneath the

machine clean, neat, and free of debris and combustible materials.
Make sure that the area overhead is clear of debris that could fall onto
or into the machine or exhaust compartment.

1.2.14 ALWAYS remove all tools, cords, and other loose items from the

generator before starting it.

1.2.15 ALWAYS make certain the machine is well-grounded and securely

fastened to a good earthen ground per national and local regulations.

1.3

Operator Safety While Using Internal Combustion Engines

Internal combustion engines present special hazards during operation
and fueling. Read and follow the warning instructions in the engine
owner’s manual and the safety guidelines below. Failure to follow the
warnings and safety standards could result in severe injury or death.

1.3.1

NEVER use this generator inside a home or garage, EVEN IF doors
and windows are open. Only use OUTSIDE and far away from
windows, doors, and vents. Using a generator indoors CAN KILL YOU
IN MINUTES. Generator exhaust contains carbon monoxide. This is a
poison you cannot see or smell.

1.3.2

NEVER use a generator inside an enclosed area such as a tunnel or a
trench.

1.3.3

Do not smoke while operating the machine.

1.3.4

Do not smoke when refueling the engine.

1.3.5

Do not refuel a hot or running engine.

1.3.6

Do not refuel the engine near an open flame.

1.3.7

Do not spill fuel when refueling the engine.

1.3.8

Do not run the engine near open flames.

1.3.9

Do not start the engine if fuel has spilled or a fuel odor is present. Move
the generator away from the spill and wipe the generator dry before
starting.

1.3.10

Refill the fuel tank in a well-ventilated area.

1.3.11

Replace the fuel tank cap after refueling.

1.3.12 ALWAYS check the fuel lines and the fuel tank for leaks and cracks

before starting the engine. Do not run the machine if fuel leaks are
present or the fuel lines are loose.

WARNING

«
...
7
8
9
10
11
...
»

Содержание GPS 8500





























































Отзывы:

Нет отзывов

Похожие инструкции для GPS 8500

Бренд: Daewoo Страницы: 49

Бренд: i-box Страницы: 4

Бренд: Harman Kardon Страницы: 2

Бренд: Hytera Страницы: 22

Бренд: CMi Страницы: 156

Бренд: König Electronic Страницы: 116

Бренд: Powermate Страницы: 16

Бренд: Matrix Страницы: 69

POF GB/UAE 1xPPR

Бренд: Datalight Страницы: 2

Бренд: Laser Страницы: 20

Бренд: iLive Страницы: 24

Бренд: Champion Страницы: 28

Бренд: Fabco Power Страницы: 13

Бренд: Soga Страницы: 28

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 22

FUJI-MICRO F4200Ri

Бренд: Baumr-AG Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды