Wabtec Ricon S Series Скачать руководство пользователя страница 28

Страница: 28 / 60

S-SERIES PRIVATE USE SERVICE MANUAL

MAINTENANCE

SEPTEMBER 2020

3 - 1

32DSST06.B

III. S-SERIES PRIVATE USE MAINTENANCE AND REPAIR

egular maintenance of the Ricon S-Series Private Use wheelchair lift will help optimize its performance and re-

duce the need for repairs. This chapter contains cleaning and lubrication instructions, maintenance schedule,

troubleshooting section, and maintenance diagrams.

CAUTION

This Ricon product is highly specialized. Maintenance and repairs must be performed by an

authorized Ricon service technician using Ricon replacement parts. Modifying or failing to

properly maintain this product will void warranty and may result in unsafe operating conditions.

A. LUBRICATION

CAUTION

Do not lubricate motor or other electrical components. Lubrication

of electrical components may create unintentional short circuits.

Lubrication should be performed at least every six months, or sooner depending on usage. Refer to

Figure 3-1

and the

following Maintenance Schedule. Lubricate lift at points specified.

B. CLEANING

Regular cleaning with mild soap (i.e. dish soap, car wash liquid) and drying thoroughly will protect lift painted surfaces.

Cleaning is especially important in areas where roads are salted in winter. Make sure that lift pivot points remain clear

and clean prior to lubrication.

C. MAINTENANCE SCHEDULE

Under normal operating conditions, maintenance inspections are required at least every six months (1750 cycles) and a

thorough inspection should be performed at service intervals referenced in

Table 3-1

. Service should be increased un-

der conditions of heavier use (more than 10 cycles per day).

TORSION SPRINGS

DETAIL "A"

TORSION SPRINGS

LUBRICATE WITH DRY LUBRICANT (GRAPHITE)

LUBRICATE WITH A PENETRATING OIL

MAY DIFFER FROM ILLUSTRATION.

NOTE:

HANDRAILS AND PLATFORM

1
2

(BOTH SIDES)

"A"

"B"

HINGE

KNUCKLE LINKS

(BOTH SIDES)

DETAIL "B"

(BOTH SIDES)

FIGURE 3-1: LIFT LUBRICATION POINTS

Содержание Ricon S Series





























































Результаты поиска

Содержание Ricon S Series

Отзывы:

Похожие инструкции для Ricon S Series

Бренды по названию

Популярные бренды

Wabtec Ricon S Series, Руководство по обслуживанию

Результаты поиска

Содержание Ricon S Series

Отзывы:

Похожие инструкции для Ricon S Series

Бренды по названию

Популярные бренды