Wabtec Ricon S Series Скачать руководство пользователя страница 23

Страница: 23 / 60

2 - 12

32DSST06.B

S-SERIES PRIVATE USE SERVICE MANUAL

INSTALLATION

SEPTEMBER 2020

TABLE 2-1: LIMIT SWITCH ADJUSTMENT CHART

COMPONENT

SYMPTOM

CORRECTIVE

ACTION

ADJUSTMENT PROCEDURE

Up cutoff

adjustment

screw

Lift stops

low.

Adjust screw

clockwise.

Adjust up cutoff switch so that lift stops just

before first knuckle actuator saddle or roller

touches underside of lower parallel arm.

(Saddle or roller should be about 1/8" from

lower parallel arm.)

Lift stops

high.

Adjust screw

counter-

clockwise.

Deploy cutoff

adjustment

screw

Lift stops

low.

Adjust screw

counter-

clockwise.

Adjust deploy limit switch so that lift stops

just below "Up" cutoff described in above

step. This will give the necessary overlap

to avoid "dead" spots.

Lift stops

high.

Adjust screw

clockwise.

END OF TABLE

PLATFORM TILT ADJUSTMENT

Correct platform tilt adjustment is crucial for proper platform rollstop operation, but cannot be adjusted at factory.

Factors such as vehicle floor height, lift tilt angle and stiffness of vehicle springs will vary installation geometry.

a. Deploy and lower lift platform to a position halfway between vehicle floor level and ground level.
b. Refer to

Figure 2-17

. Adjust left and right platform set screws until platform is level at zero (0) degrees.

Turn setscrews clockwise to angle front-end of platform upward, or counter-clockwise to angle downward.

NOTE:

At ground level, the distance between heel of platform and ground should be 3/4" to 1". This distance

should be measured at initial point of rollstop full deployment.

NOTE:

Adjust setscrews on both sides of platform simultaneously and evenly to ensure proper leveling of platform.

RSM0003400

SET SCREW

S-SERIES TYPE PLATFORM

FIGURE 2-17: PLATFORM SET SCREWS

c. Repeat steps a and b as required to achieve proper rollstop operation.

Содержание Ricon S Series





























































Результаты поиска

Содержание Ricon S Series

Отзывы:

Похожие инструкции для Ricon S Series

Бренды по названию

Популярные бренды

Wabtec Ricon S Series, Руководство по обслуживанию

Результаты поиска

Содержание Ricon S Series

Отзывы:

Похожие инструкции для Ricon S Series

Бренды по названию

Популярные бренды