manualshive.com logo in svg

VWR International 1917, Инструкция по установке и эксплуатации

Поделиться
Скачать
VWR International 1917 Скачать руководство пользователя страница 19

 

19

4/ condensation collecting on CO2 sensor 
5/ CO2 sensor or interface failure 
6/ unit incorrectly calibrated, see section 5.11 
8/ taking Fyrite reading too soon after the door has been opened 
9/ air leak around CO2 sensor mounting plate 

MECHANICAL 

Door not sealing 

 

 

1/ check physical condition of gasket  
2/ confirm that door latch pulls door in tightly  
3/  assure that gasket is in original location 

Motor doesn't move 
 

1/ if shaft spins freely: check connections to motor and check 
voltage to motor;  
2/ if shaft rubs or is frozen, relieve binding and retest 

Motor makes noise 
 

1/ If noise is from the motor, tap the top of motor shaft with ball 
peen hammer.  
2/ If the sound gets worse, tap the other end of the shaft - 
avoiding touching the fan blade.  
3/ If there is no change, call Customer Service. 
4/ If noise is from shaft or fan blade, realign shaft.  

Solenoid valve buzzing 

 

 

After removing solenoid clean with alcohol for carbon build-up 
then blow out.  Check valve seat or channels for contamination.  
Check CO2 filter and/or grade of CO2 used.  If seat is worn, 
replace. 

OTHER 

Controller on at all times - "locked-up"   
 

1/ Adjust set point to room temperature.  If the light goes out but is 
still heating, replace the solid state relay.  
2/ turn unit off and on to reset 
3/ if cannot change any condition on the front panel, call Customer 
Service 

Front panel displays are all off 

 

 

1/ Check for wire damage. 

unit or wall fuse/circuit breaker is 
blown 

 

 

1/ check wall power source 
2/ compare current draw and compare to specs on data plate 
3/ see what other loads are on the wall circuit 

unit will not turn on 

 

 

1/ check wall power source  
2/ check fuse/circuit breaker on unit or in wall  
3/ see if unit is on, e.g., fan or heater, and just controller is off   
4/ check all wiring connections, esp. around the on/off switch   

Unit is smoking – Out of box 

 

 

Put unit under vent and run at full power for one hour. 

Contamination in chamber 

 

 

1/ see cleaning procedure in operator’s manual 
2/ develop and follow Standard operating procedure for specific 
application; include definition of cleaning technique and 
maintenance schedule. 

Содержание 1917

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды