VTech LS1250-B Скачать руководство пользователя

Страница: 65 / 69

there is no chime

from the doorbell

when it is pressed.

Make sure you install two AA batteries and

connect AC power supply to the doorbell.
The doorbell light on the doorbell flashes when

the doorbell is pressed. If the light doesn’t flash,

the doorbell may have run out of battery. You may

need to replace new batteries.
Make sure the doorbell is registered to the

telephone system.
Make sure your handset is in reception range and

works probably.
Make sure the chime volume of your handset is

not set to off.
If there is an incoming call when the doorbell

is pressed, the handset will not respond to the

chime.
When three or more system handsets are in

use for a call at a time, video streaming will be

disabled.
If you have more than one doorbell, make sure the

other doorbell is not in use for video streaming.

Only one doorbell can be used for video streaming

at a time.
If the previous suggestions do not work, deregister

all devices and register them to the telephone

base again.

•

common cure for

electronic equipment.

If the telephone is not responding normally, put the

handset in the telephone base. If it does not respond, try

the following (in the order listed):

Disconnect the power to the telephone base.
Disconnect the batteries on the handset.
Wait a few minutes before connecting power to the

telephone base.
Re-install the batteries and place the handset in the

telephone base.
Wait for the handset to synchronize with the

telephone base. Allow up to one minute for this to

take place.

•
•
•

•

This telephone is not equipped with a grounding function. Therefore, some of the

functions may be limited when used in PBX systems. Please contact the technical

support of the network provider for further information.

Содержание LS1250-B





































































Результаты поиска

Содержание LS1250-B

Отзывы:

Похожие инструкции для LS1250-B

Бренды по названию

Популярные бренды

VTech LS1250-B, Руководство пользователя

Результаты поиска

Содержание LS1250-B

Отзывы:

Похожие инструкции для LS1250-B

Бренды по названию

Популярные бренды