background image

 3-15/64”(82mm)

Wing center section

WARNING ! Securely install the receiver and power
pack, ensuring they will not come loose or rattle during
flight.
Never fly before checking the Cg’s required position.

In order to obtain the CG specified, reposition the receiver and power pack

WARNING

Do not put in a large-than recommended engine. A bigger engine does not necessarily mean better performance.

IMPORTANT:

Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner 
to clean on surface of your model to keep the colour not fade.

Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. 
Peel off one corner of the backing and cut off with scissors. 
Arrange sticker on model and when satisfied adhere the corner without backing.
Carefully peel back the rest of the backing while at the same time adhering the rest of the sticker.

Try not to make air bubbles, if there are some, carefully puncture sticker (center of bubble) but not model surface with the 
tip of the knife or sharp pin and squeeze out the air. 
At curves stretch sticker and apply a little heat so that no ceases occur. 
Cut off the excess that is produced.

219995

Betty Lou

“3

rd

FRESNO

CALIF

Snoohs

2

ND

VQA091

VQA09

26- BALANCE

27- DECALS

VQ MODELS. P-39 Q/N  .46 SIZE

VQ MODEL / P-39Q/N VERSION 1

VQA09 DECAL SHEET

VQA091 DECAL SHEET

    VQA091 
DECAL SHEET

Содержание P-39 Q/N AIRACOBRA













Отзывы: