background image

Manual DINAMO Plug & Play 

 

Control your miniature world 

Page 18 of 32 

Version 1.2 – Dec 21

st

, 2017 

2017 Leon van Perlo 

If you have the OC32/NG in enclosure, simply mount the OC32/NG using the 4 screws that 
come with the unit or enclosure to a suitable flat surface. As with the bare unit, make sure 
to allow for enough space to insert the connectors including cables and make sure you can 
still access the dipswitches at the side. 
 

4.4

 

OC32/NG Power Supply 

 
The power for the OC32 and the devices controlled by the OC32 can be derived from the 
power supply used for your trains (read: the TM44), or you choose one or more separate 
power supplies for your OC32(‘s). Which choice you make depends on the optimal Voltage 
you need to drive your accessories and the amount of power you need. 
 
If you use multiple power supplies, make sure the negative poles (minus or 0V terminals) of 
all the power supplies in your system are connected to each other. 
 
The power supply for your OC32 and connected devices shall always be a positive DC supply! 
Most devices that, according to the manufacturer, need AC current, can be fed with DC 
current without any problem. Should you have devices that absolutely need AC current, use 
a relay to switch them. 
  
The supply for the OC32 is connected to pin 1 (+) and 2 (-) on the 4-pole connector. See 
fig 17.  
 
 
 
 
 
 
 
 

 

Fig 17: Connecting power supply to the OC32 
 
 

PWR  GND

DO NOT CONNECT!

PWR  GND

DO NOT CONNECT!

Control your miniature world 

 

Manual DINAMO Plug & Play 

 

2017 Leon van Perlo  

Version 1.2 – Dec 21

st

, 2017 

Page 15 of 32 

If you want to connect 4 sections per block, at the side you connect to the TM44, bundle all 
white wires and put then in the terminal for the A-rail. The individual colours (blue, orange, 
green, brown) are used as B0 - B3. 

At the track-side, connect the colours blue, orange, green and brown to the B-rail of the 
corresponding section. Connect the white wire of the same pair to the opposite side of the 
track. In this way you feed the track at multiple locations which helps preventing problems 
with bad rail contacts. 

If you do not need 4 sections per block, you may use each wire-pair as an individual wire. On 
both ends bundle the coloured and white wire of each pair. This way you will effectively have a 
cable with 4 conductors with a cross section of 0.4mm

2

 each to connect up to 3 sections 

per block. 

The best way to connect the wire to the track is soldering it to the outer side or bottom of 
the rail. Soldering to the bottom is usually only possible when you have not laid your track 
yet. The advantage is that it is invisible. The disadvantage is that maintenance can be 
problematic. If the wire breaks you won’t be able to reconnect it the way you originally did. 
 

Содержание Dinamo

















Отзывы: