voran EBP580 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 52

voran EBP580 Скачать руководство пользователя страница 13

Single belt press EBP580

Version: 166000000, M0017267B_EN208-240-60D
Date: 28.11.2017

- 13 / 52 -

1.8 Correct use

This machine/line is intended and constructed for the following use in full compliance with the contractual terms:

INFORMATION!

The press may only be used for the pressing of fruit, vegetables and herbs that contain juices.

The stones must be removed from all stone fruit, unless the stones are no bigger than cherry pits
and do not have sharp edges (danger of breaking screen belt).

Any other use of this machine/line represents an improper use of the machine/line.
The correct use of this machine/plant to terms of the contract requires further that the documentation/Operating
Manual as also the specified inspection and servicing intervals are strictly adhered to.

Although this machine/plant has been constructed to the highest technical standards and the recognised standards of
safety and has been accepted by the client, danger of injury or of loss of life may none-the-less arise for the user or
third persons as a result of its use, or the machine/line may itself be damaged.

The machine/line may only be operated when in a technically perfect condition, in a professional manner and when
the operator is fully aware of the safety and danger aspects.

Recognized weaknesses or faults that may reduce the safety of operation, must be dealt with in a professional
manner immediately or must be reported to customer service in a manner that can be proven!

Changes must not be made to the machine/line settings values.

WARNING AGAINST GENERAL DANGERS

This machine/line was constructed to the current standards of engineering and the currently
applicable Safety of Machinery Directive (MSV) .

Non-observation of the safety regulations contained in the Operating Manual during operation
of the line/machine can endanger the operating staff or third persons or have a detrimental
effect on the line/machine or its properties.

1.9 Inappropriate use

WARNING AGAINST GENERAL DANGERS

Any use of this machine/line other than that as defined in the chapter "Correct Use", represents an
inappropriate use of the machine/line and can result in serious injuries of the operating staff or third
persons or to the damage or destruction of the line/machine.

The manufacturer/supplier cannot be held liable for any damage resulting from an inappropriate use of
the machine/line.

In such cases the user assumes full liability.

«
...
11
12
13
14
15
...
»

Содержание EBP580





















































Отзывы:

Нет отзывов