Von Duprin 3350AWDC Скачать руководство пользователя

Страница: 16 / 16

Printed in U.S.A.

24739476 Rev. 4/15-b

Customer Service

1-877-671-7011

www.allegion.com/us

TROUBLESHOOTING

If latches do not retract when pushpad is depressed:

Remove cover plate from edge of door

Pull

down

top spool input

. If the top latch fails to actuate, readjust top spool (Steps 4d-1 thru 4d-4).

Pull

bottom spool input

. If the bottom latch fails to actuate, readjust bottom latch clearance (Steps 8b-1 thru 8b-4).

If both actuate and the door is not functioning, proceed to next check.

Remove center case cover

Check

lift finger screws

to ensure they are still fully seated. If unseated, loosen

locking

screw

, and while applying pressure to the head of the

lift finger screw

seat it, tighten locking screw. If door is not functioning, proceed to next step.

With

both

lift finger screws

fully seated, loosen

top and bottom locking

screws

, turn

lift finger screws

clockwise to end of travel, and repeat

device adjustment, Step 6.

If bottom spool input does not move during Steps 6b-2 / b-3:

Loosen

bottom spool screw

10 turns.

If the 33/3550AWDC center case cover is difficult to install:

Loosen bottom screw installed in Step 5c

and lift rod connector sleeve until it will go no higher, then retighten screw.

Seated

Unseated

Содержание 3350AWDC

















Результаты поиска

Содержание 3350AWDC

Отзывы:

Похожие инструкции для 3350AWDC

Бренды по названию

Популярные бренды

Von Duprin 3350AWDC, Руководство по установке

Результаты поиска

Содержание 3350AWDC

Отзывы:

Похожие инструкции для 3350AWDC

Бренды по названию

Популярные бренды