Volvo EPA2007 D13F Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 179

background image

BASIC SERVICE 149

Installation

1. Install a new gasket between the catalytic filter module and the DPF filter module.

2. Align the locator tab located on the bottom of the DPF filter module with the slot
located in the top of the catalytic filter module. Install the DPF filter module onto
the catalytic filter module and secure the modules together using a V-band clamp
tightened to specification.

3. Install a new gasket between the outlet module and the DPF filter module.

W2033384

4. With assistance, use a suitable lifting device to install the outlet module onto
the DPF filter module. Ensure that the differential pressure tube does not become
damaged during outlet module installation.

Note:

Make sure the high-temperature gasket remains in place and has not become

dislodged.

5. Install the V-band clamp to secure the outlet module to the DPF filter module
and tighten clamp fasteners to specification. All clamps should now be aligned and
tightened.

6. Install the pressure differential tube to the port on the catalytic filter module and
tighten the fitting securely.

Note:

A high-temperature anti-seizing compound should always be applied to the

threads of the sensors, plugs or fittings in the exhaust system to avoid component
seizure or corrosion.

«
...
153
154
155
156
157
...
»

Содержание EPA2007 D13F




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EPA2007 D13F

Бренд: YOODA Страницы: 6

Бренд: Flux Страницы: 28

Бренд: ACM Страницы: 36

Бренд: TCF Страницы: 16

Бренд: Raider Страницы: 28

Бренд: Saito Страницы: 5

Бренд: Saito Страницы: 6

Бренд: Detroit Diesel Страницы: 22

Concept engines

Бренд: RB Страницы: 19

Бренд: Cors-Air Страницы: 10

Бренд: Black Bruin Страницы: 4

Бренд: Toyota Страницы: 407

Бренд: CERTIFIED Страницы: 17

Бренд: M.T.H. Страницы: 28

Бренд: Daedong Страницы: 68

Parilla MINI SWIFT

Бренд: IAME Страницы: 31

Бренд: Associated Electrics Страницы: 4

Бренд: Nanni Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды