Volvo EPA2007 D13F Скачать руководство пользователя страница 146

Страница: 146 / 179

140 BASIC SERVICE

Full-Flow Main Filter Replacement

To replace the full-flow main filter:

1 Make sure the filter casing is thoroughly cleaned. If not already done, wash the

area around the filter mounting adapter with a suitable solvent and blow dry with
compressed air.

2 Put a suitable container in place to collect spillage.

3 Using a filter wrench, remove the filter casing from the mounting bracket and

discard it.

4 Apply a thin film of clean engine oil to the sealing gasket of the new filter.

5 Screw the new dry filter in place and tighten an additional 3/4 to 1 turn by hand

after the gasket contacts the base.

6 If necessary, replace the water separating pre-filter. See the preceding instructions.

7 Start the engine and run at idle for five minutes to fill the filter with fuel.

8 Check for leaks.

CAUTION

Severe engine damage may be caused by attempting to prime the fuel system using
an auxiliary pump or by applying air pressure in the fuel tank. These techniques
may destroy seals that prevent fuel from leaking into the crankcase.

Cooling System Maintenance

Note:

SPECIAL TOOL J48061 WILL BE NEEDED.

Coolant Drain Outlets

Extra outlets provide convenient drain sites for use during maintenance and other
procedures involving coolant.

Содержание EPA2007 D13F




















































































































































































Результаты поиска

Содержание EPA2007 D13F

Отзывы:

Похожие инструкции для EPA2007 D13F

Бренды по названию

Популярные бренды

Volvo EPA2007 D13F, Справочное руководство

Результаты поиска

Содержание EPA2007 D13F

Отзывы:

Похожие инструкции для EPA2007 D13F

Бренды по названию

Популярные бренды