Voltronic Power +Power 30U-120 Скачать руководство пользователя страница 14

Страница: 14 / 58

3.3

Control Panel & interface

The front access Graphic Display & Control interface brings all measured parameter, UPS & Battery

current states and Alarms. Through the interface, users can easily monitor status and configure
settings. For detailed information, please refer to the charter 4.

Figure 3-7: Control Panel

3.3.1 LED indications

LED

Color

Status

Definition

INPUT

Green

Input source is normal.

Flashing

Input source is abnormal.

Off

No input source

BYPASS

Green

Load on Bypass.

Flashing

Input source is abnormal.

Off

Bypass not operating.

INVERTER Green

Load on inverters.

Off

Inverters not operating.

BATTERY

Yellow

Load on Battery.

Flashing

Low battery

Off

Battery converter is normal and battery is charging.

ALARM

Red

UPS fault.

Flashing

UPS alarm.

Off

Normal.

3.3.2 LCD Display

Graphic display and all measured parameters.

Содержание +Power 30U-120



























































Результаты поиска

Содержание +Power 30U-120

Отзывы:

Похожие инструкции для +Power 30U-120

Бренды по названию

Популярные бренды

Voltronic Power +Power 30U-120, Руководство пользователя

Результаты поиска

Содержание +Power 30U-120

Отзывы:

Похожие инструкции для +Power 30U-120

Бренды по названию

Популярные бренды