OPERATING INSTRUCTIONS
VERSION 08/12
UTPS-40 TABLET POWER ADAPTOR
ITEM NO.: 515200
INTENDED USE
This product is designed to supply USB devices and tablet computers with power, providing five different output voltages
to select from. The connected load’s current consumption must not exceed the maximum output rating of the product.
Power is supplied via a standard mains socket (100 - 240 V/AC, 50/60 Hz). The product should only be used in dry
indoor areas. The product features both short-circuit and overload protection.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product for
purposes other than those described above, the product may be damaged. In addition, improper use can cause
hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and product
names are trademarks of their respective owners. All rights reserved.
DELIVERY CONTENT
• Tablet power adaptor
• USB cable
• 7 x connector plugs (3 x DC hollow socket, 4 x microUSB type B)
• Voltage setting key
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety information. If you do
not follow the safety instructions and information on proper handling in this manual, we assume
no liability for any resulting personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the
product.
• Also observe the safety and operating instructions of any other devices which are connected to the
product.
• The mains outlet must be located near to the device and be easily accessible.
• As power supply, only use the supplied mains adaptor.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
shop.
If you are not sure about the correct connection or use, or if questions arise which are not covered by these operating
instructions, please do not hesitate to contact our technical support or another qualified specialist.
OPERATION
a) Connecting an electric load
• Disconnect the power supply unit from the mains socket before replacing the low-voltage plug
or resetting the output voltage.
• The power adaptor‘s output voltage must match the input voltage of the electric consumer.
1. Set the required output voltage with the voltage selection switch, using the voltage setting key. When making
settings always be sure the arrow points accurately to the respective voltage marking.
2. Select one of the three low-voltage plugs (DC hollow socket) matching the input socket and polarity of the electric
consumer (see table).
The connector at the end of the output cable can be plugged directly into the consumer. The outer / inner diameter of
the plug is 5.5 / 2.5 mm. Insert the plug into a consumer of a compatible size, then continue with point 5.
3. Connect the plug to the connector at the end of the output cable. Voltage reversal of the output plug is not possible
for security reasons. The inner contact is positive (+), the outer negative (–).
4. Connect the low-voltage plug to the switched-off consumer.
5. Connect the mains plug to a standard mains socket (100 - 240 V/AC, 50/60 Hz). The VOLTCRAFT logo on the top
of the power adaptor lights up to indicate operational readiness.
6. Now switch the connected consumer on. If it does not function properly, switch it off immediately and disconnect
it from the power supply unit.
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the
time of printing.
© Copyright 2014 by Voltcraft®
V3_0814_02_JH
7. Remove the power supply unit from the mains when it is no longer in use.
b) Connecting a USB load
1. Select one of the four low-voltage plugs (microUSB type B) matching the input socket of the electric consumer
(see table).
2. Connect the plug to the connector at the end of the USB cable.
3. Connect the switched-off consumer to the low-voltage plug.
4. Connect the USB cable to the power adaptor.
The power adaptor can also be used to operate / charge a normal USB device. Plug the USB plug of the
device into the USB socket and continue with point 5.
5. Connect the mains plug to a standard mains socket (100 - 240 V/AC, 50/60 Hz). The VOLTCRAFT logo on the top
of the power adaptor lights up to indicate operational readiness.
6. Now switch the connected consumer on. If it does not function properly, switch it off immediately and disconnect
it from the power adaptor.
7. Remove the power adaptor from the mains when it is no longer in use.
The USB output and other electric loads can be operated in parallel. However, make sure that the power input
of the connected devices does not exceed the power supply unit’s total power output.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
TECHNICAL DATA
Operating voltage:
100 - 240 V/AC, 50/60 Hz
Output voltage / current:
5 V/DC, 2100 mA (USB)
9 / 10.5 V/DC, 3000 mA ±10 %
12 / 15 / 19 V/DC, 1500 mA ±10 %
Max. output power:
40 W
Operating temperature:
0 to +35 ºC, 20 – 85 % RH
Storage temperature:
-20 to +50 ºC, 10 – 90 % RH
Dimensions (W x H x D):
35 x 108 x 70 mm
Weight:
235 g
a) Connector plugs (microUSB type B)
Imprint
Plug
Plug Ø (outer / inner)
Suitable for
DC3
4.0 / 1.7 mm
Sony P tablet
DC6
3.0 / 1.1 mm
Huawei tablet
Red dot
–
iPhone / iPad
Grey dot
–
Samsung Galaxy Tab
b) Connector plugs (DC hollow socket)
Imprint
Plug
Plug Ø (outer / inner)
Suitable for
M08Q
2.0 / 0.6 mm
Motorola tablet
MND
3.2 / 0.9 mm
Acer tablet
MNX
4.0 / 1.7 mm
Toshiba / Viewsonic tablet
