Vollrath STOELTING Flavor Burst STL-80BLD-DLX Скачать руководство пользователя страница 65

Страница: 65 / 80

4. Remove the open-close bushing from the

plate and wrap the bushing around the
pump harness cable, leaving enough cable
to connect the end to the electronics board.
Snap the grommet with the cable back into
the slotted hole in the plate.

5. Reinstall the cover plate to the electronics

box.

6. Connect the pump harness cable to the

electronics board port labeled “BANK A” or
“PWRCONN2”.

7. Reinstall the cover to the electronics box.

Use the 8 screws to secure the assembly.

8. Ensure the power-switch is in the “off”

position with the “

○

” end pressed in on the

electronics box power entrance module.

9. Connect the Drive Motor Cable to the round

metal port.

10. Connect the ethernet cable to the ethernet

port in the plastic gland. Screw the plastic
cover over the connection and secure the
ethernet gland assembly with the nut.

11. Connect the power cord to the port on the

back panel.

Содержание STOELTING Flavor Burst STL-80BLD-DLX

















































































Результаты поиска

Содержание STOELTING Flavor Burst STL-80BLD-DLX

Отзывы:

Бренды по названию

Популярные бренды

Vollrath STOELTING Flavor Burst STL-80BLD-DLX, Руководство оператора

Результаты поиска

Содержание STOELTING Flavor Burst STL-80BLD-DLX

Отзывы:

Бренды по названию

Популярные бренды