manualshive.com logo in svg

Vollrath STOELTING Flavor Burst STL-80BLD-DLX, Руководство оператора

Поделиться
Скачать
Vollrath STOELTING Flavor Burst STL-80BLD-DLX Скачать руководство пользователя страница 63

60 

 

Connecting the Unit Syrup Line and Pump 
Harness Cable 
 

The syrup lines attached at the lower back of 
the cabinet connect the 8 bags of syrup to the 
Blending Assembly, with the 9

th

 tube connecting 

the sanitizer tank to the Blending Assembly.  
For protection during the shipping process, the 
9-Tube Lead is stored inside the back of the 
cabinet.   Likewise, the pump harness cable will 
also need to be installed in place outside the 
cabinet.   
 
1.  Remove the small screws on the back panel 

of the Cabinet. 

 

 

 

 

2.  Carefully remove the panel and set it aside.   

 

 

 

 
3.  Locate the 9-Tube Lead.  Remove the dust 

cap and slide the coupler casing down.   

 

 

 

 

 

4.  Loosen the Lead’s coupler nut and slide the 

connection onto the slot on the lower plate.  

 

 

 
 

5.  Tighten the coupler nut and the casing to 

secure. 

 

 

 
 

6.  Connect the 9-Tube Lead with the 9-Tube 

Assembly, with the 9-hole gasket in 
between.  Align the 9-hole gasket with the 
coupler pins of the 9-Tube Lead and place 
the gasket against the coupler.  Then align 
the coupler pins of the two tube assemblies 
and connect them.     

 

 

 
 

Содержание STOELTING Flavor Burst STL-80BLD-DLX

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды