manualshive.com logo in svg

Vollrath STOELTING Flavor Burst STL-80BLD-DLX, Руководство оператора

Поделиться
Скачать
Vollrath STOELTING Flavor Burst STL-80BLD-DLX Скачать руководство пользователя страница 64

61 

 

7.  Thread the 9-Tube Assembly coupler nut 

onto the Lead’s casing and tighten to 
secure.   

 

 

 

 

NOTE:  

THE 44-SYSTEMS WITH THE SPLIT 

LEAD WILL CONNECT WITH THE TWO 9-
TUBE ASSEMBLIES OUTSIDE THE CABINET.   

 
 

8.  Gently lay the pump harness cable out and 

away from the cabinet.  Remove the open-
close bushing from the plate and wrap the 
bushing around the pump harness cable 
near the lower plate’s slotted hole.  Snap 
the grommet with the cable back into the 
slotted hole in the plate.       

 

 

 
 

Installing the Electronics Box and Power 
Connections  
 

The electronics box houses the electronics 
board and most of the power connections for 
the Deluxe unit.  For shipping safety purposes, 
the electronics box ships unconnected to the 
unit.   Follow these instructions to install the 
electronics box to the back of the Deluxe 
cabinet, connect the remaining power cables, 
and power up the system.   
 
1.  Remove the electronics box cover by 

unscrewing the 4 screws on each side. 

 

 

 

 

2.  Remove the two screw from the cover plate 

and gently pull the plate away from the 
electronics box. Leave the Drive Motor 
cable connected to the board.   

 

 

 

 
3.  Insert the white plastic end of the pump 

harness cable (from the back of the cabinet) 
through the opening where the cover plate 
was on the electronics box.   

 

 

 

 

Содержание STOELTING Flavor Burst STL-80BLD-DLX

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды