background image

Page 3

Processor

 Series

acoustics

TO PREVENT ELECTRIC SHOCK, DO NOT  

REMOVE  TOP  OR    BOTTOM  COVERS.   

NO  USER  SERVICEABLE  PARTS  INSIDE. 

REFER  SERVICING  TO  QUALIFIED 

SERVICE  PERSONNEL.  DISCONNECT 

POWER  CORD  BEFORE  REMOVING 

REAR  PANEL  COVER  TO  ACCESS  GAIN 

SWITCH.

Shock Hazard - Do Not Enter

Choc Hasard - N*entrent

Schocke Hazard - Test Nicht 

                              Betrete

Urto Hazard - Do  Non Entrano

WARNING

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT EXPOSE THIS

EQUIPMENT TO RAIN OR MOISTURE!

Magnetic Field

CAUTION:

 Do not locate sensitive high-gain equipment such as preamplifiers or tape decks 

directly  above  or  below  this  unit.  Because  this  amplifier  has  a  high  power  density,  it  has  a 

strong magnetic field which can induce hum into unshielded devices that are located nearby. 

This  field  is  strongest  just  above  and  below  the  unit.  If  an  equipment  rack  is  used,  we 

recommend  locating  the  amplifier(s)  at  the  bottom  of  the  rack  and  the  preamplifier  or  other 

sensitive equipment at the top.

The  lightning  bolt  triangle  is 

used alert the user to the risk 

of electric shock

The exclamation point triangle is used 

to alert the user to important operating 

and/or maintenance instructions.

Printed on 
recycled paper.

Содержание RESONATOR













Отзывы: