VNS Therapy SENTIVA M2000 Wand Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 81

VNS Therapy SENTIVA M2000 Wand Скачать руководство пользователя страница 72

72

Patient Cannot Feel Magnet Stimulation

• Possible causes:
- Patient has become accustomed to the programmed setting
- Incorrect technique for swiping magnet
- Magnet output current is programmed to 0 mA
- Generator battery at end of service (EOS)
- Device implanted too deep in the chest
- Defective generator or disabled generator
- “High” lead impedance
- Short-circuit condition within the lead

“Cannot feel magnet activation”

Interrogate the

generator

Record the CAUSE

“The generator is currently

disabled due to [CAUSE].

The generator is NOT supplying

stimulation.”

Note: If the CAUSE is “a wand

reset” and the reset was

intended, continue with the

session

• Display Device History or Events

• Record number of magnet

activations

• Swipe the magnet

• Reinterrogate the device

• Display Device History or Events

Magnet settings

may be too low for

patient to perceive.

Consider adjusting

magnet setting

Lead Impedance

“High” or “Low”

See

“Troubleshooting”

in the

programming

system Physician’s

Manual

Lead Impedance “Ok”.

Output Current “Ok”

Magnet Mode

stimulation is

functioning properly

and the patient

may have become

accustomed to the

settings. Consider

raising the magnet

current if perceived

stimulation is desired

Lead Impedance “Ok”.

Output Current “Low”

Generator cannot

deliver the

programmed magnet

output due to

increased impedance.

Consider lowering

magnet output current

while increasing

magnet pulse width

Indication that the

generator did not

sense a magnet.

Swipe the magnet

again and repeat

Magnet Mode

Diagnostics. If the

message appears

again call Technical

Support

Contact LivaNova Technical Support

Yes

Yes

No

No

Yes

No

“Disabled Message?”

Is Magnet Current

≥

the

Output Current? and

Magnet ON time

>7 seconds?

Did the magnet

activations increase?

Patient Report

• Perform a System Diagnostics

• Record results

Generator is delivering the magnet stimulation.

Consider raising the magnet current if perceived

stimulation is desired

«
...
70
71
72
73
74
...
»

Содержание SENTIVA M2000 Wand


















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды