manualshive.com logo in svg

VKB Gunfighter Mk.II, Быстрое руководство

Поделиться
Скачать
VKB Gunfighter Mk.II Скачать руководство пользователя страница 9

 

9

VKB Gunfighter Mk.II Quick 
Guide - SOFTWARE

Note

: It is highly recommended to right-click on the VKBdevCfg app and select ‘

Run

 

as

 

Administrator’

.

Note

: If ZBootloader-C says "Device is not ready", please check whether VKBdevCfg is not shut down. 

Additionally, you might see this error message when some 3rd party software (e.g., Logitech 

or

 Razor or 

whatever else) has grabbed the joystick and established control over it. Ensure that all 3rd party software of 
this kind is temporarily disabled while you're updating the firmware.

Flash

 your Gunfighter’s BlackBox firmware:

1. Launch VKBdevCfg-C.
2. In the top panel, click on the "VKBsim Gunfighter..." name to select it.
3. From the Tools tab, click on the "Bootloader" icon; this should close VKBdevCFG and automatically start 

ZBootloader-C (if you have it in the same folder).

4. Point ZBootloader-C to the extracted *.vkb file and update the firmware of your BlackBox by clicking 

"Flash It".

5. The device will restart with the new firmware installed.

Содержание Gunfighter Mk.II













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды