VKB Gunfighter Mk.II Скачать руководство пользователя страница 8

Страница: 8 / 12

VKB Gunfighter Mk.II Quick
Guide - SOFTWARE

To get started, follow these three steps:
1. Download the

latest

(by date) VKBdevCfg-C app - (http://ftp.vkb-sim.pro/Programms/) and extract

it to any folder you like.

2. Download the

latest

(by date) ZBootloader-C app - (http://ftp.vkb-sim.pro/Programms/) and

extract it into the same folder as above.

3. Download the

latest

(by date) BlackBox firmware for Gunfighter (

http://ftp.vkb-sim.pro/Firmware/BlackBox/) (usually identified by BB_GF_

version

) and extract the

firmware (*.vkb) from either the KG12, MCG or MCG PRO archive respectively, and put it into the

same folder where your VKBdevCfg app already is.

From here on out, there are

three

basic

steps

involved in the overall process:

●

Flash

your Gunfighter’s BlackBox with the new firmware.

●

Reset

your Gunfighter to factory default.

●

Calibrate

your Gunfighter.

Содержание Gunfighter Mk.II













Результаты поиска

Содержание Gunfighter Mk.II

Отзывы:

Бренды по названию

Популярные бренды

VKB Gunfighter Mk.II, Быстрое руководство

Результаты поиска

Содержание Gunfighter Mk.II

Отзывы:

Бренды по названию

Популярные бренды