Note.
extra monitor
FUNCTIONAL CHECK AND OPERATION ORDER
Note.
Special notes on operation with BKM-440
main
extra
main
intercom priority
extra
main monitor’s
extra
extra
main
Image capture
To capture visitor’s image during intercom
To set the monitor on automatic image capture
Note.
Viewing captured images
-01
-02
Note.
If your monitor is connected to Commutator BKM-440 as an
(see Fig. 7), then individual settings for the
first and second doorstation are not available, settings will be the same for both doorstations. To perform settings, make
a call to the monitor from either connected doorstation.
Then select a ring tone, set its volume, adjust brightness, contrast and saturation as described above.
When a call is made from the doorstation, the monitor rings. Image from the doorstation camera appears on the screen.
Pick up the handset and check duplex intercom. During intercom, press
to view image from the extra camera (see Fig. 4,
5, 6), if needed. Press
again to switch back to the image from the doorstation camera.
To release the door lock, press
and hold for 1 second (until a beep). The door is unlocked now. After you release the
button, intercom is still available. Hang up the handset. The screen shuts off, the monitor goes to the Stand-By mode.
You can unlock the door without picking up the handset. When called, just press and hold
until the beep. The
door is unlocked now. After you release
, the monitor goes to the Stand-By mode.
To activate the individual / storey doorstation (i.e. start intercom and video monitoring on your initiative, see Fig. 5), pick
up the handset. Image appears on the screen, intercom is available. You can press
to view image from the extra
camera, if needed. Press
again to switch back to the image from the doorstation camera.
At pressing the door bell button, the monitor rings, image from the extra camera appears on the screen (see Fig. 4, 5).
To engage the sleep mode, press
and hold until the Power LED turns off.
The monitor can be connected to the BKM-440 either as the
(see Fig. 6) or the
monitor (see Fig. 7). The
monitor has an
over any
device, i.e. when you pick up the
handset, the
monitor (or extra apartment handset) is disengaged. The
monitor cannot activate the individual / storey
doorstation.
To view the door zone in front of main entrance doorstation (see Fig. 6), press
on the
monitor, or pick up its
handset. To switch to viewing the door zone in front of individual / storey doorstation, press
again. To start intercom
with the individual / storey doorstation, pick up the handset.
, press the
button on your monitor, when image from the camera is on the
screen.
, press the
button, when the monitor is on stand-by.
The LED indicator for AWAY mode starts to illuminate.
The monitor captures an image in 3 seconds after a call starts. The LED indicator blinks if there are new images in the
monitor’s memory.
To quit automatic image capture mode, press the
button, when the monitor is on stand-by. The LED indicator for AWAY
mode goes out.
The monitor’s memory is capable to store 64 images. If the memory is full, a new image forces out the oldest one from
the archive.
To start viewing captured images, press either
or
. The screen switches on and shows the newest captured image. In
the lower part of the screen there are time, date and number of the image displayed. The newest image has number
. A
previous image has number
, and so on.
Press either
or
to view previous or next image respectively.
To quit viewing press
.
The monitor automatically quits viewing:
- in 40 seconds, if you do not push any button;
- when being called from the doorstation.
Captured images are always B/W disregarding the type of camera (either B/W or colour).
www.
201 -1 )
VIZIT-M440CM Operating Instruction (revision
5 2
vizit-group.com
8 9
/
