background image

ENGLISH

THANKS FOR CHOOSING ONE OF OUR PRODUCTS.

Mounting the Wall Plate to the Wall

Insert the Locking Bar and attach the Monitor to Wall Plate

Step 2B

Step 3

Warning: Some monitors may require two people to lift!

Insert the Locking Bar (c) to the Wall Plate (a) as shown in the Diagram 3a. If necessary add a padlock (not 

supplied) at the end of the locking bar. Hook the Monitor Brackets (b) over the top of the Wall Plate (a) and 

then let the bottom of the Monitor Brackets rotate to the bottom of the Wall Plate as shown in the Diagram 

3b. Push the bottom of the monitor to lock the Monitor Brackets on 

the Wall Plate, as shown in the Diagram 3c. Loose the knobs on both 

Monitor Brackets to adjust the tilt angle according to your requirement. 

Pull out the Locking Bar first if you want to remove the monitor from 

the Wall Plate. 

Wood Stud mounting:

The Wall Plate (a) must be mounted to two studs at least 16” (406 mm) 

apart. Use a stud finder to locate two adjacent studs. It is a good idea 

to verify where the studs are located with an awl or thin nail. Pre-drill a 

50 mm deep hole at the desired height in each stud using a 4 mm drill 

bit. Make sure these holes are in the center area of the studs and level 

with each other. Use the Wall Plate as a template to mark the location 

of the second hole in each stud. Drill 50 mm deep holes using the 3.8 

mm drill bit in the marked locations. Attach the Wall Plate to the wall 

using the 4 Lag Bolts (n) and 4 Lag Bolt Washers (o).

8

n

o

a

c

a

3a

3b

b1 ,b 2

a

3c

Содержание VLMW4065T









Отзывы: