background image

Warranty 

Warranty 

The 

Vitrek

 instrument is warranted against defects in material and workmanship 

for a period of one year after the date of purchase.  

Vitrek

 agrees to repair or 

replace any assembly or component (except batteries) found to be defective, 
under normal use, during the warranty period.  

Vitrek's

 obligation under this 

warranty is limited solely to repairing any such instrument, which in 

Vitrek's

 

sole opinion proves to be defective within the scope of the warranty, when 
returned to the factory or to an authorized service center.  Transportation to the 
factory or service center is to be prepaid by the purchaser. Shipment should not 
be made without prior authorization by 

Vitrek

.   

The warranty does not apply to any products repaired or altered by persons not 
authorized by 

Vitrek

, or not in accordance with instructions provided by 

Vitrek

.  

If the instrument is defective as a result of misuse, improper repair, or abnormal 
conditions or operations, repairs will be billed at cost. 

Vitrek

 assumes no responsibility for its product being used in a hazardous or 

dangerous manner, either alone or in conjunction with other equipment.  Special 
disclaimers apply to this instrument. 

Vitrek

 assumes no liability for secondary 

charges or consequential damages, and, in any event, 

Vitrek's

 liability for breach 

of warranty under any contract or otherwise, shall not exceed the original 
purchase price of the specific instrument shipped and against which a claim is 
made. 

Any recommendations made by 

Vitrek

 or its Representatives, for use of its 

products are based upon tests believed to be reliable, but 

Vitrek

 makes no 

warranties of the results to be obtained.  This warranty is in lieu of all other 
warranties, expressed or implied, and no representative or person is authorized 
to represent or assume for 

Vitrek

 any liability in connection with the sale of 

Vitrek

 products other than set forth herein. 

Instrument Serial Number: __________________________________ 

Содержание XiTRON XT560

























Отзывы: