Vitek VT-8306, Инструкция по эксплуатации

Страница: 3 / 24

3
ENGLISH
IRON VT-8306 G
The iron is intended for ironing clothes and bedding
and for vertical steaming of fabrics.
DESCRIPTION
1. Water spray
2. Water inlet lid
3. Continuous steam supply knob
4. Water spray button
5. Burst of steam button
6. Handle
7. Power cord protection
8. Base of the iron
9. On/off indicator of the heating element
10. Water tank
11. Temperature control knob
12. “MAX” water level mark
13. Soleplate
14. Self-cleaning button
15. Beaker
SAFETY MEASURES
Attention!
For additional protection it is reasonable to install a
residual current device (RCD) with nominal operation
current not exceeding 30 mA. To install RCD contact
a specialist.
SAFETY MEASURES
Before using the unit, read this instruction manual
carefully and keep it for future reference.
Use the unit for its intended purpose only, as speci-
fied in this manual. Mishandling the unit can lead to
its breakage and cause harm to the user or damage
to his/her property.
•
Before switching the unit on, make sure that
your home mains voltage corresponds to the iron
operating voltage.
• The power cord is equipped with a “europlug”;
plug it into the socket with a reliable grounding
contact.
•
To avoid fire, do not use adapters for plugging
the unit in.
• To avoid mains overloading, do not switch on sev-
eral electrical appliances with high power con-
sumption at a time.
•
Do not use the iron outdoors and in rooms with
high humidity.
• Place the iron on a flat stable surface or use a sta-
ble ironing board.
•
Attention! The surfaces of the iron get hot during
operation. Keep open skin areas away from iron
hot surfaces or outgoing steam to avoid burns.
• Do not fill the water tank with scented liquids, vin-
egar, starch solution, descaling reagents, chemi-
cals etc.
•
Provide that the power cord is not on the ironing
board and make sure that it does not touch hot
surfaces or sharp edges.
•
Do not leave the unit unattended. During breaks
in operation put the iron on the base (in vertical
position).
• Before plugging/unplugging the iron, set the tem-
perature control knob to the minimum position
and switch the continuous steam supply off.
•
Always unplug the iron when you are not using
it. Always take the power plug out of the mains
socket before filling the water tank.
•
The water inlet lid should be closed during ironing.
•
To unplug the iron, always hold the power plug; do
not pull the power cord.
•
To avoid electric shock, do not immerse the iron,
the power cord and the plug into water or any
other liquids.
•
Before taking the iron away, let it cool down com-
pletely and pour out the remaining water.
•
Pour out water from the water tank only after
unplugging the iron.
•
Never leave the plugged in iron unattended.
•
Clean the unit regularly.
•
Do not touch the unit body and the power
plug with wet hands.
• Do not allow children to touch the unit body and
the power cord during the iron operation.
•
Do not leave children unattended to prevent using
the unit as a toy.
•
For children safety reasons do not leave polyeth-
ylene bags used as packaging unattended.
Attention! Do not allow children to play with poly-
ethylene bags or packaging film. Danger of suf-
focation!
•
This unit is not intended to be used by children.
Place the unit out of reach of children during the
operation and cooling down.
• The unit is not intended to be used by physically
or mentally disabled persons (including children)
or by persons lacking experience or knowledge
if they are not under supervision of a person who
is responsible for their safety or if they are not
instructed by this person on the usage of the unit.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty cer-
tificate and on the website www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
• There may be water residue in the tank, this is
normal, as the iron has undergone factory qual-
ity control.
IM VT-8306.indd 3 21.11.2017 12:46:35