Vitek VT-8118, Инструкция по эксплуатации, Страница: 5 / 28

5
ENGLISH
•
Never use the unit if the power adapter or
connecting cord is damaged, if the unit works
improperly or after it was dropped.
•
Do not attempt to repair the vacuum cleaner.
Do not disassemble the vacuum cleaner by
yourself, if any malfunction is detected or
after it was dropped, unplug the unit and apply
to any authorized service center at the con-
tact addresses given in the warranty certifi-
cate and on the website www.vitek.ru.
• To avoid damages, transport the unit in the
original package only.
•
Keep the unit in a dry cool place out of reach
of children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
–
Unpack the unit, remove any stickers and
package materials that can prevent the vac-
uum cleaner operation.
–
Check the unit for damages; in case of dam-
ages do not use the unit.
Before switching the unit on, make sure that your
home mains voltage corresponds to the power
adapter operating voltage.
ASSEMBLING THE VACUUM CLEANER
Base
Insert the vertical stand (20) into the base (22)
until the clamp (25) clicking. To disassemble the
base press the clamp (25) and disconnect the
base (22) (pic. 1).
Battery charging
Before using the vacuum cleaner for the first time
or after a long period of inactivity, the battery
needs to be charged for 6-8 hours.
A fully charged battery provides approximately
20 minutes of continuous vacuum cleaner opera-
tion at maximal power level and about 35-40 min-
utes of operation at low power level.
•
To charge the battery place the vacuum
cleaner on the base (20-22).
• Insert the power adapter (26) cord plug into
the connection socket (21).
•
Plug the power adapter (26) into the mains
socket, light segments will light up on the
charge/operation indicator (15).
•
When the battery charging cycle is finished,
all segments of the indicator (15) will glow
constantly.
Notes:
–
charge the battery of the vacuum cleaner at
the temperature from +5°C to +35°C.
–
if you haven't used the unit for a month or lon-
ger, charge the battery completely before
using the vacuum cleaner.
USING THE VACUUM CLEANER
Attention! Switch the vacuum cleaner on only
with the dust bin (3), the prefilter (17) and
the HEPA filter (16) installed in the dust bin.
Always check if the dust bin (3) is assembled
and installed properly.
• Use the base (20-22) for easy storing of the
vacuum cleaner or vacuum cleaner battery
charging.
• Take the unit by the handle (5) and remove the
vacuum cleaner from the base (20-22). During
the operation or when carrying the vacuum
cleaner hold the unit by the handle (5).
•
Press the on/off button (6) to switch the vac-
uum cleaner on, the vacuum cleaner will be
switched on at the maximal power, the light
segments which show the battery charg-
ing rate will light up on the charge/operation
indicator (15), the electric brush (2) will be
switched on and the electric brush lighting (1)
will be switched on.
•
You can switch on or off the electric brush
(2) by pressing the button (9), the lighting (1)
is switched on during the electric brush (2)
operation.
• Use the electric brush (2) for cleaning floors
and carpets with medium and low pile, the
brush (2) is perfect for removing pet hair from
carpets. The round brush is brought to rota-
tion by an electric motor built in the brush (2),
its bristles thoroughly comb out pet hair and
sweep motes out of the carpet pile.
Notes:
–
do not use the electric brush (2) if the pile
length exceeds 15 mm.
–
do not run the brush (2) over electric wires.
•
During the vacuum cleaner operation you can
select the vacuum cleaner operating modes
by pressing the buttons (7, 8).
IM VT-8118.indd 5 02.04.2018 16:59:16