Vitek VT-2329, Инструкция по эксплуатации

Страница: 4 / 16

4
ENGLISH
•
Never block the air inlets of the hairdryer, do
not place the hairdryer on a soft surface, such
as a bed or couch, where the air inlets may be
blocked. Keep the air inlets free of lint, dust,
hair etc.
• Avoid getting of hair into the air inlet grid dur-
ing operation of the unit.
•
It is recommended to unwind the power cord
to its full length while using the unit.
• The power cord should not:
–
touch hot objects,
–
run over sharp edges,
–
be used as a handle for carrying the unit.
• Check the power cord and power plug insula-
tion integrity periodically.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
• Transport the unit in the original package
only.
•
For environmental protection do not dispose
of the unit with usual household waste after
its service life expiration; apply to a special-
ized center for further recycling.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
USING THE HAIRDRYER
After unit transportation or storage under
cold (winter) conditions, it is necessary to
keep it for at least two hours at room tem-
perature before switching on.
• Before switching the unit on, make sure that
your home mains voltage corresponds to the
operating voltage of the hairdryer.
•
Unwind the power cord completely.
• Insert the power plug into the mains socket.
• Use the switch (6) to set the required air sup-
ply speed, the operation indicator (2) will
light up:
«
0 » – the hairdryer is off;
– low speed;
– high speed.
•
Set the required temperature of the air flow
using the switch (5):
– low heating;
– medium heating;
– maximal heating.
Note: During the first operation some for-
eign smell and a small amount of smoke
from the heating element is possible, this
is normal.
Hair care
To get the best results, wash your hair with sham-
poo (before drying and styling), dry it with a
towel to remove excessive moisture and comb
your hair.
Quick drying
Set the switch (5) to the maximal heating
position (position
). Use the switch (6) to set
the required air supply speed and dry your hair.
Shake off excessive moisture from the hair with
your hand or a comb and constantly move the
hairdryer above your hair.
Straightening
Set the switch (5) to the maximal heating posi-
tion (position
). Use the switch (6) to set the
required speed of air supply and dry your hair
first. When the hair is almost dry, set the noz-
zle (1), decrease the heating degree using the
switch (5) and decrease the air supply speed
using the switch (6).
Divide your hair into locks and layers and start
straightening from the lower layers. Using a
plain or a round brush, comb the hair down-
wards and simultaneously direct hot air
from the nozzle at your hair. This way, slowly
straighten each lock from root to end. After you
finish straightening the locks of the lower hair
layer, start straightening the locks of the mid-
dle layer and finish with the locks of the upper
hair layer.
Natural wavy hair structure
Set the switch (5) to the low heating position
(position ), select the low air supply speed,
setting the switch (6) to the position
, grip
locks between fingers, turn them in the direc-
tion of natural curling and dry them directing
air between fingers. When the required effect is
achieved, press the cool shot button (4)
and
fix each lock.
VT-2329.indd 4 16.11.2017 16:48:48