Vitek VT-1467 GY, Руководство пользователя

Страница: 5 / 46

5
ENGLISH
• To switch the blender on press and hold the
button (2). Use this operation mode for mix-
ing liquid products.
• If you press and hold the button (3), the unit
will operate at maximum rotation speed.
• After you finish using the unit, take the plug
out of the socket, disconnect the whisk (7)
from the gear (6) and disconnect the gear (6)
from the motor unit (4) turning it clockwise.
Attention!
–
Do not use the whisk (7) to kneed tight
dough.
–
Products for beating/mixing should be put
into the bowl before switching the unit on.
USING THE CHOPPING KNIFE (18)
Attention!
–
Do not chop very hard products, such as nut-
megs, coffee beans and cereals.
Before you start chopping:
–
Remove bones, veins and cartilage from
meat.
–
Cut meat, onion, garlic, carrots etc. into
approximately equal slices.
–
When chopping greens, remove stems of
herbs.
Chopping
Warning:
–
Before assembling make sure that power
plug is not inserted into the socket.
–
Do not overfill the processing bowl.
Caution: The blades are very sharp!
• Set the driving shaft (19) on the spindle of the
processing bowl (17).
• Remove the plastic protective cover from the
blades of the knife (18) and set the knife in
the slots of the driving shaft (19).
• Put the products into the processing bowl
(17).
• Put the geared lid (10) on the bowl (17).
• Press the lock button (16) and turn the geared
lid (10) counterclockwise, setting it to the
position “ ”, release the lock button (16)
and make sure that the geared lid (10) is fixed
properly.
• Place the motor unit (4) on the geared lid
(10) and rotate it clockwise until it is securely
fixed.
• Insert the power plug into the socket.
• Set the required speed from 1 to 20 using the
control knob (1).
• To switch the blender on press and hold the
button (2).
• When the button (3) is pressed, the knife
rotates at maximum rotation speed.
• Hold the motor unit (4) with one hand and
the bowl (17) with the other hand during
operation.
• After using the unit remove the power plug
from the socket, disconnect the motor unit
(4) from the geared lid (10), turning it coun-
terclockwise.
• Then remove the geared lid (10) from the
bowl (17), pressing the lock button (16) and
turning the lid (10) clockwise.
• Carefully remove the knife (18) gripping the
upper end of the driving shaft (19).
• Take the chopped products out of the pro-
cessing bowl (17).
• Clean, wash and dry all the used parts imme-
diately after operation.
• Put the knife (18) into the plastic protective
cover.
Attention! Continuous operation time of the
unit should not exceed 20-30 seconds.
USING THE CUBIC ATTACHMENT
Use the cubic attachment for cutting fruit and
boiled vegetables.
Attention!
–
Do not process hard and frozen food. It can
damage the cubic attachment.
Warning:
–
Before assembling make sure that the power
plug is not inserted into the socket.
• Open the clamps (14), set the knife (12) on
the cubic attachment (13) and fix it with the
clamps (14).
• Match the groove on the cubic attachment
(13) with the ledge inside the processing
bowl (17) (near the bowl handle) and install
the attachment in the bowl
(PIC. 1).
• Set the driving shaft (11) into the attach-
ment (13).
Note: Check whether the attachment (13) is set
properly, otherwise the processor lid (10) will
not close.
• Put the geared lid (10) on the bowl (17).
• Press the lock button (16) and turn the
geared lid (10) counterclockwise to the posi-
VT-1467.indd 5 18.10.2012 15:06:31