Vitek VT-1251, Инструкция по эксплуатации

Страница: 6 / 48

6
ENGLISH
DRY IRONING
• Place the iron on the base (11).
• Insert the power plug into the outlet.
• Set the temperature regulator (13) to the
required ironing temperature: “ • ”, “ •• ”,
“ ••• ” or “ max ” (depending on the type
of fabric), the (7) indicator will light up
(Pic.3).
• When the sole temperature (17) reaches
the desired temperature value, the (7) indi-
cator will go out, you can start ironing.
• After you finish ironing set the (13) regula-
tor to the “min” position .
• Pull the plug out of the socket and let the
iron cool down completely.
STEAM IRONING
For steam ironing set the temperature regu-
lator to «
••• » or « МАХ ». The iron has an
anti-drop valve, which stops water supply,
when the sole temperature is too low it pre-
vents the appearance of drops out of the sole
openings (17). While heating or cooling down
of the sole (17), you will hear clicks of open-
ing/closing of the anti-drop valve it means
that the valve works normally.
• Place the iron on the base (11).
• Insert the power plug into the outlet.
• Make sure that there is enough water in the
water tank (12).
• Set the temperature regulator (13) to the
required ironing temperature: “ ••• ” or
“ max ” (depending on the type of fabric),
the (7) indicator will light up (Pic.3).
• When the sole temperature (17) reaches
the desired temperature value, the (7) indi-
cator will go out, you can start ironing.
• Turn the steam supply regulator (3) to set
the intensity of steaming, steam will start
outgoing from the openings of the sole
(17).
• After you finish ironing set the (13) regula-
tor to the “min” position and the steam
supply regulator (3) to the left position .
• Pull the plug out of the socket and let the
iron cool down completely.
ATTENTION!
If during the operation steam is not constant-
ly supplied, check whether the temperature
regulator (13) is set properly.
ADDITIONAL STEAM RELEASE
Additional steam release function is use-
ful when ironing folds and can only be used
at high ironing temperatures (when the iron
temperature regulator (13) is set to “
••• ” or
“ max ”).
• When the additional steam release button
(6) is pressed, steam will be vigorously re-
leased from the openings in the iron sole
(pic.5).
Note: In order to avoid leakage of water
from steam openings, press the addition-
al steam supply button (6) with 4-5 sec.
interval.
VERTICAL STEAMING
For vertical steaming can be used only when
the high temperature mode is used (set
the temperature regulator (13) to «
••• » or
« МАХ »).
• Hold the iron vertically at the distance 15-
30 cm from the clothes press the addition-
al steam release button (6), steam will be
released from the openings in the iron sole
(17) (pic. 6).
Important information
• Vertical steaming is not recommended for
synthetic fabrics.
• To avoid melting the fabric, do not touch
the iron sole to the item while steaming.
• Never steam iron clothing that is being
worn as the steam temperature is very high
and it can cause burns. Use a coat-hanger
or a stand.
AUTO-SWITCH OFF FUNCTION
If the iron is about 30 seconds in the horizon-
tal position or about 8 minutes in the vertical
position it will switch off automatically. The
(8) indicator will be flashing.
To switch on the iron, just start ironing.
Note: After switching off of the iron the
preset temperature of the iron sole will be
1251.indd 6 1251.indd 6 02.06.2008 12:01:29 02.06.2008 12:01:29