manualshive.com logo in svg

Vislink ADVENT DCU5000, Руководство по эксплуатации

Поделиться
Скачать
Vislink ADVENT DCU5000 Скачать руководство пользователя страница 18

Advent Communications 

209297 – DCU5000 Drive Control Unit 

Page 18 of 42 

 

4.39.  F39: FAN POWER SUPPLY ALARM 

The internal heatsink fan power supply is out of specification. 

4.40.  F40: BRAKE POWER SUPPLY ALARM 

The brake power supply is out of specification. Either the supply has been shorted on 
the antenna, or an internal DCU5000 supply rail has failed. 

4.41.  F41: FEED POWER SUPPLY ALARM 

The DCU5000 does not have a feed power rail. This alarm should never be triggered, if 
seen please report the occurrence to Advent Communications customer support. 

4.42.  F42: GPS/COMPASS POWER SUPPLY ALARM 

The GPS/Compass power supply is out of specification. Either the supply has been 
shorted on the antenna, or an internal DCU5000 supply rail has failed. 

4.43.  F43: STATUS POWER SUPPLY ALARM 

The DCU5000 does not have a status power rail. This alarm should never be triggered, 
if seen please report the occurrence to Advent Communications customer support. 

4.44.  F44: AZ BRAKE DISCONNECTED 

The DCU5000 is expecting a brake to be fitted on the azimuth axis. The brake has not 
been detected on power-up. 

4.45.  F45: EL BRAKE DISCONNECTED 

The DCU5000 is expecting a brake to be fitted on the elevation axis. The brake has not 
been detected on power-up. 

4.46.  F46: POL BRAKE DISCONNECTED 

The DCU5000 is expecting a brake to be fitted on the polarisation axis. The brake has 
not been detected on power-up. 

4.47.  F47: AXIS 4 BRAKE DISCONECTED 

The DCU5000 does not have an axis 4 drive. This alarm should never be triggered, if 
seen please report the occurrence to Advent Communications customer support. 

4.48.  F48: AXIS 5 BRAKE DISCONNECTED 

The DCU5000 does not have an axis 5 drive. This alarm should never be triggered, if 
seen please report the occurrence to Advent Communications customer support. 

4.49.  F49: MAIN UNIT FAN SERVICE 

The main unit fan run time has exceeded the service time programmed. Consider 
replacing the DCU5000 main cooling fan, contact Advent Communications customer 
support for further information. 

4.50.  F50: HEATSINK FAN SERVICE 

The heatsink fan run time has exceeded the service time programmed. Consider 
replacing the DCU5000 heatsink cooling fan, contact Advent Communications 
customer support for further information. 

4.51. F51: 

E

2

PROM CHECKSUM ERROR 

A checksum error has been detected in a page of the E

2

PROM memory area. 

4.52.  F52: SOFTLIMIT DATA ERROR 

An error has been detected whilst reading the units softlimit settings. The values have 
been set to their default values. If the antenna system requires restricted antenna 
movement, check values and confirm the safe operation of the antenna system. 

Содержание ADVENT DCU5000











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды