5. Installation
8. Specification
Problems
Troubleshooting
Nothing appears on the
screen.
The image on the
screen is dim.
The image on the
screen is dark.
The camera is not working
properly, and the surface
of the camera is hot.
The screen flickers
continually.
RS-485
Communic-ation fails.
Color is not correct.
*Specifications are subject to change without prior notice for better improvement.
6. Troubleshooting
7. Dimension (mm)
- How to use tactile switch on the OSD control
DOWN (D)
UP (U)
MENU
(PUSH)
LEFT (L)
RIGHT (R)
Push – to enter the menu or to save settings.
Push up or down – select functions.
Push left or right – to adjust levels.
5-4. OSD Manual for functions control
(Menu Tree)
For detailed information regarding OSD menu, refer to ‘OSD Manual for
Effio-E Cameras’.
95.7
122
85.2
Ø88
74.8
179.5
247.3
White Balance
1,800˚K ~ 10,500˚K Auto
(ATW/ Push/ Push lock/ User 1/2, Anti CR, Manual)
Gain Control
Standard : -6dB ~ 44.8dB Auto
Smear Effect
0.005%
Power source
12VDC
Operating current
120mA/12VDC(IR Off), 340mA/12VDC(IR On)
Lens(Standard)
2.8-12mm Varifocal DC Auto Iris lens
Lens(Option)
3.6mm/ 6mm Fixed lens
LED Spectrum
850nm
Viewable Distance
Up to 30M at Moonless Night
MTBF of IR
20,000 hours
Iris Control
Auto
Operating temp
./Humidity
-10°C ~ 50°C (Humidity : 0% RH ~ 90% RH),
Option : -40°C ~ 50°C(-40°F ~ 122°F)
IP Rating
66
Measurement (mm)
88(D) x 247.3(L)
Weight (Approx.g)
1,000
I
mage sensor
Effective Pixels
NTSC : 976(H) x 494(V), PAL : 976(H) x 582(V)
H. Resolution
650TV Lines(Color) / 700TV Lines(B/W)
Synchronizing system
Internal
Scanning system
NTSC : 525 Lines PAL : 625 Lines 2:1 Interlaced
Video output
1.0Vp-p Composite 75 Ohms
S/N ratio
More than 52dB (AGC Off)
Min. Illumination
0Lux
Shutter Speed
NTSC:1/60~1/10,000 sec. PAL:1/50~1/10,000 sec.
Gamma Correction
Standard γ = 0.45
Class
Supuer Night Vision Outdoor Camera
1/3" Sony 960H Ex-view HAD CCD
Ⅱ
5-5. Waterproof processing of cable end connection
Make sure to use a butyl tape. (Do not use a sealing material on those parts)
①
It is useful to connect the cable ends from camera to the extension cable for waterproof.
②
Connect and tape the power cables (Power-Power/Ground-Ground).
③
Bind the power cables together with the tape. When DC-Jack is used, tape the DC-DC joint.
④
Connect and tape the RS485 cables (RS485+
_
TRX+ /RS485-
_
TRX-)
⑤
Tape the BNC-BNC joint.
a. Power cable
b.
RS-485 : Same as above
c. Video output cable
(Red)
(Black)
Please make sure to seal these places
with a tape tightly enough to prevent
water smearing into the cable.
A lot of actual damages are happening by
doing improper finish on the spot.
* Caution
If there are problems in operating, please refer to the checklist below.
If the problem persists, please contact the agent where this product is purchased.
· Please check that the power cord and line connection between the
camera and the monitor are fixed properly.
·
Please check that you have properly connected VIDEO cable to the
camera VIDEO output jack.
· Please check that you have properly connected the camera to
an appropriate power source.
·
Please check the setting of WHITE BAL Setup menu .
· Please check that direction of camera turns toward the Sun.
· Please check the polarity between RS-485 Control Port and
RS-485 cable.
· Please check if the initial value of the RS-485 Communication setup
matches between camera and OSD Controller or DVR.
· RS-485 Communication establishment initial value.
· We recommend that you make ground connection between camera
and controller for safe communication control.
·
When RS-485 cable is not properly connected, A warning message
‘ERROR RS-485 Connection. Please reconnect and Reboot’ is
displayed.
Then please turn off the power and connect the cable again.
·
Adjust the contrast feature of the monitor.
·
If you have an intermediate device, set the 75Ω / Hi-Z properly
(Please check the impedance)
·
Is the lens stained with dirt? Clean your lens with soft,clean cloth.
· Set the monitor to proper condition.
·
If the camera is exposed to too strong light, change the camera
position.
485 Control Board Connection Port
(+)CONNECTION TERMINAL(TRX+)
( )CONNECTION TERMINAL(TRX )
RS-485 Control Port
485+
485
Item
Initial value
1
9600
8-NONE-1
ENABLE
Camera ID
BAUD RATE
UART MODE
RET PKT
Shutter/ AGC
Auto / Manual
White Balance
ATW / Push / Push Lock / User 1, 2/ Anti CR/ Manual
Picture Adjust
Mirror(On/Off), Brightness, Contrast, Sharpness, HUE, Gain
ATR
On / Off
Privacy Mosaic
Back Light
Off / BLC / HLC
On / Off (4 Zone setting available)
Day / Night
AUTO / COLOR / B/W
NR
NR Mode / Y Level / C Level
Camera ID
On / Off
Language
English / Germany / French / Russian / Spanish
Portuguese / Japanese
FUNCTION
S
HU
TTER
/A
GC
AU
TO
HI
G
H
L
U
M
INANC
E
MODE
BR
I
G
H
TNESS
LOW L
U
M
INANC
E
MODE
BR
I
G
H
TNESS
RET
UR
N
M
ANUA
L
MODE
S
HU
TTER
A
GC
RET
UR
N
W
HI
TE B
A
L
A
TW
SPEED
DEL
AY
CNT
A
TW F
RA
ME
ENV
I
ROMENT
RET
UR
N
P
U
S
H
U
SER1
B-G
AI
N
R-G
AI
N
RET
UR
N
U
SER2
B-G
AI
N
R-G
AI
N
RET
UR
N
AN
T
I
CR
M
ANUA
L
LEVEL
RET
UR
N
P
U
S
H
LOC
K
P
I
CT
A
DJ
U
ST
M
I
RROR
BR
I
G
H
TNESS
CONT
RA
ST
S
HAR
PNESS
HU
E
G
AI
N
RET
UR
N
B
ACKLI
G
H
T
OFF
/
BLC
/ H
LC
ATR
LUMINANCE
CONTRAST
RETURN
OFF
ON
LANGUAGE
CAMERA RESET
SAVE ALL
PRIVACY
ON
OFF
AUTO
DAY/NIGHT
BURST
DELAY CNT
DAY NIGHT
NIGHT DAY
RETURN
COLOR
B/W
BURST
IR OPTIMIZER
MODE
LEVEL
NR
NR MODE
Y LEVEL
C LEVEL
RETURN
CAMERA ID
ON
OFF
English / Germany / French / Russian / Spanish
Portuguese / Japanese
120924-1
