background image

 
                                                                                     

 

2- 

  1. Safety Instruction   

     

 

 

WARNING 

 

  Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that 

they also receive this instruction booklet. 

 

Caution

 

  All fixtures are intact from the manufacturer, please operate follow up the user manual, artificial fault 

are not under guarantee repair. 

  Unpack and check carefully there is no transportation damage before using the unit

 

  The unit is for indoor use only. Use only in a dry location

 

  Do install and operate by operator

 

  Use safety chain when fixes the unit

 

  The  unit  must  be  installed  in  a  location  with  adequate  ventilation,  at  least  50cm  from  adjacent 

surfaces.   

  Be sure that no ventilation slots are blocked, otherwise the unit will be overheated. 

  Before  operating,  ensure  that  the  voltage  and  frequency  of  power  supply  match  the  power 

requirements of the unit. 

  It’s important to ground the yellow/green conductor to earth in order to avoid electric shock. 

  Maximum ambient temperature TA : 40

. Don’t operate it where the temperature is higher than this.

 

  Don’t connect the device to any dimmer pack. 

  First run, there will be smoke or smells, and all disappearing a few minutes later. 

  Make sure there are no flammable materials close to the unit while operating, as it is fire hazard. 

  Look over power wires carefully, replace immediately if there is any damage. 

  Unit  surface  temperature  may  reach  up  to  60

.  Don’t  touch  the  housing  bare

-hand  during  its 

operation. 

  Never run on for a long time lest shortening lifespan. 

  Avoid any inflammable liquids, water or metal objects entering the unit. Once it happen, cut off the 

mains power immediately. 

  Do not operate in dirty and dusty environment, also cleaning fixtures regularly. 

  Do not allow children to operate the fixture. 

  Do not touch any wire during operation as there might be a hazard of electric shock. 

  Avoid power wires together arounding other cables. 

  Replace fuse only with the same type. 

  In the event of serious operating problem, stop using the unit immediately. 

  Never turn on and off the unit time after time. 

Please read the instructions carefully which includes important 

information about the installation, operation and maintenance. 

UnRegister

ed

Содержание BW-54-3RGBW IV

















Отзывы: