background image

Iss 8 - Mar 2019 

 

Page 2 of 9 

This guide is intended to instruct in the proper installation of a Viridian EV  charge point.  Please note 
that when installing this equipment care must be taken to ensure that all local and national safety and 
planning requirements are met. 
 

INSTALLATION OF THIS EQUIPMENT SHOULD ONLY BE CARRIED OUT BY A 

FULLY QUALIFIED INDIVIDUAL.  VIRIDIAN EV ACCEPTS NO RESPONSIBILITY FOR 

DAMAGE CAUSED BY IMPROPERLY INSTALLED EQUIPMENT. 

 

Cautions and Dangers 

This guide contains several instructions to which the following symbols have been attached.  Failure to 
comply with instruction could result in: 

DANGER

 

Indicates where failure to comply with instructions will cause death or serious 
injury.  

WARNING

  Indicates where failure to comply with instructions could lead to death or 

serious injury. 

CAUTION

  Indicates  where  failure  to  comply  with  instructions  could  lead  to  minor  or 

moderate injury. 

 

This document is intended to instruct in the installation of all models of Viridian manufactured charge 
points (current model numbers at the time of writing listed below).  Instructions specific to particular 
models will be highlighted and clearly marked.  
 
M03-T1C-16A-1P 
M03-T2C-16A-1P 
M03-T2S-16A-1P

M07-T1C-32A-1P 
M07-T2C-32A-1P 
M07-T2S-32A-1P

M12-T2C-16A-3P 
M12-T2S-16A-3P 
M22-T2C-32A-3P 
M22-T2S-32A-3P 

Understanding the model number of your charge point 

 
 

 

M07-T2S-32A-1P 

 
 
 

 

 

Approximate 
maximum available 
power in kWh 
Example: 7kWh 

Enclosure Type 
Example: Metal 
Enclosure 

Connector Type 
Example: Type 2 

Socket or cable 
(Socket type 2 
only) 
Example: Socket 

Maximum Available 
Current per phase 
Example: 32A 

Number of phases 
Example: Single 
Phase 

Содержание M03-T1C-16A-1P










Отзывы: