Viridian EV EcoLite Basic Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 15

Viridian EV EcoLite Basic Скачать руководство пользователя страница 3

Install manual: Viridian EV EcoLite

®

Basic charge point

Iss 3 - Apr 2019

Page 3 of 15

WARNING

The EcoLite

®

charge point range is designed for electric vehicle (EV) charging only. It is designed to

only allow the flow of electricity once an EV is connected and correct communication is established.

Any tampering of the charge point to allow the flow of electricity at any times other than this will

present a risk of electric shock.

CAUTION

The charge point is covered by a manufacturer’s parts and labour warranty. Alterations to the charge

point that are not permitted will invalidate this warranty. See viridianev.co.uk/resources for further

warranty information

Fig. A - Charge point external features

1.

Socket outlet (for Free/Socket versions)

2.

Status LED text and halo

3.

Identification label (side) (illustrated Fig b)

4.

Electrical protection access panel & key-lock

5.

Socket weather drain tube (bottom) or tethered cable outlet

2

1

3

4

5

«
1
2
3
4
5
...
»

Содержание EcoLite Basic
















Отзывы:

Нет отзывов