Viper 791 XV, Руководство по установке

Страница: 54 / 58

5 54 4
© 2005 Directed Electronics, Inc. Vista, CA
ttrroouubblleesshhoooottiinngg
■
SSh ho occkk sseen nsso orr d do oeessn n''tt ttrriig gg geerr tth hee aallaarrm m::
Has the NPC® system been triggered? If so, you will hear 5 chirps when disarming. To check this, turn the igni-
tion key on and off to clear the NPC®'s memory, and then retest the shock sensor. For a detailed description of
NPC®, see Nuisance Prevention Circuitry section of this guide.
■
D Do oo orr iin np pu utt d do oeess n no ott iim mm meed diiaatteellyy ttrriig gg geerr ffu ullll aallaarrm m.. IIn nsstteeaad d,, cch hiirrp pss aarree h heeaarrd d ffo orr tth hee ffiirrsstt 3 3 sseecco on nd dss::
That's how the progressive two-stage door input works! This is a feature of this system. This is an instant trigger,
remember, since even if the door is instantly closed again, the progression from chirps to constant siren will continue.
■
CCllo ossiin ng g tth hee d do oo orr ttrriig gg geerrss tth hee ssyysstteem m,, b bu utt o op peen niin ng g tth hee d do oo orr d do oeess n no ott::
Have you correctly identified the type of door switch system? This happens often when the wrong door input has
been used. (See Door Lock Harness Wire Connection Guide section of this guide.)
■
SSyysstteem m w wiillll n no ott p paassssiivveellyy aarrm m u un nttiill iitt iiss rreem mo otteellyy aarrm meed d aan nd d tth heen n d diissaarrm meed d::
Are the door inputs connected? Is the H1/6 blue wire connected to the door trigger wire in the vehicle? Either
the H1/5 green or the H1/7 violet should be used instead. (See wiring diagrams.)
■
D Do oo orr iin np pu utt d do oeess n no ott rreessp po on nd d w wiitth h tth hee p prro og grreessssiivvee ttrriig gg geerr,, b bu utt w wiitth h iim mm meed diiaattee ffu ullll aallaarrm m::
Does the Status LED indicate that the trigger was caused by the shock sensor? (See Diagnostics section of this
guide.) The shock sensor, if set to extreme sensitivity, may be detecting the door unlatching before the door
switch sends its signal. Reducing the sensitivity can solve this problem.
■
TTh hee V Vaalleett//P Prro og grraam m ssw wiittcch h d do oeessn n''tt w wo orrkk..
Is it plugged into the correct socket? See Plug-In LED and Valet/Program Switch section of this guide.
■
SSttaattu uss LLEED D d do oeessn n''tt w wo orrkk..
You've probably guessed already, but here goes: Is it plugged in? (See Plug-In LED and Valet/Program Switch
section of this guide.) Is the LED plugged into the correct socket?
■
D Do oo orr llo occkkss o op peerraattee b baacckkw waarrd dss..
This unit has easily-reversed lock/unlock outputs. Recheck wire connections to see if you have reversed these.
■
TTh hee rreem mo ottee ssttaarrtt w wiillll n no ott aaccttiivvaattee..
1. Check the harnesses and their connections. Make sure that the harnesses are completely plugged into the
remote start module. Make sure there are good connections to the vehicle wiring.
rreem moottee ssttaarrtt ttrroouubblleesshhoooottiinngg
aallaarrm m ttrroouubblleesshhoooottiinngg