background image

TOP OF LADDER 

BOTTOM OF LADDER 

13.4 

13.5 

13.7 

13.2 

13.1 

13.3 

13.  VERY IMPORTANT

VERY IMPORTANT

VERY IMPORTANT

VERY IMPORTANT - SECURE IN-POOL LADDER SECTION. The inside / in-pool ladder section F must 

be secured in place for greater strength & stability. The inside ladder section MUST NOT be allowed to 
slide  up. Identify  the  inside  / in-pool  side of your  ladder  with the  “missing” hardware connection points 
from steps 9 & 10. Make certain ladder section F is all the way to the bottom. At the four bolt locations 
identified in 13.1 (left from step 9 & 10 - see 13.4 & 13.5), pass a 2-1/2 carriage bolt through the open bolt 
hole, from the outside in, and secure using a washer and nut (13.7). The bolts will pass through an open 
slot in the ladder section at all four corners (see 13.2, 13.3 & 13.6), two at the top of the ladder section 
and two at the bottom. Tighten all four bolts equally to slightly beyond snug - as you tighten, you will see 
the washer and nut pull the ladder section tight to the support frame. Do not over-tighten.  

13.6 

15.  Position  ladder  in  the  pool  at  desired  location 
(15.1)  making  certain  the  anti-entrapment  barrier  is 
away from the pool liner. Position ladder above an up-
right  support  post  of  pool  for  greater  stability  (15.2). 
You  MUST

MUST

MUST

MUST  secure  the  ladder  to  the  pool  top  rail  for 

strength & stability. The top platform of the ladder has 
4  possible  bolt  holes;  choose  2  that  best  suit  your     
positioning & pool top rail. Mark bolt locations on pool 
top rail & drill 1/4" holes. Using the 3" bolts, washers & 
nuts,  secure  ladder  to  top  rail  (15.3).  Tighten          
hardware.  IMPORTANT

IMPORTANT

IMPORTANT

IMPORTANT:  When  pool  is  not  in  use  slide 

up  exterior  ladder  section  &  secure  with  lock  (15.4). 
Remove & store for pool closure / winterization. 

14.    VERY  IMPORTANT

VERY  IMPORTANT

VERY  IMPORTANT

VERY  IMPORTANT  -  COMPLETE  ASSEMBLY  AND  INSTALLATION  OF  ANTI-ENTRAPMENT  LADDER 

BARRIER  ON  REVERSE  OF  THIS  PAGE  BEFORE  INSTALLING  LADDER  INTO  THE  POOL.  The  barrier  is 
included  with  this  ladder  to  prevent  children  from  swimming  through  or  behind  pool  ladder.  Failure  to 
complete assembly & installation may result is serious personal injury or drowning. 

SLIDE & 

SLIDE & 

SLIDE & 

SLIDE & 

LOCK WHEN 

LOCK WHEN 

LOCK WHEN 

LOCK WHEN 

NOT IN USE

NOT IN USE

NOT IN USE

NOT IN USE    

SWIM

SWIM

SWIM

SWIM    

SAFELY

SAFELY

SAFELY

SAFELY    

15.1 

15.2 

15.3 

15.4 

Revised Instruction SLA - 1/8/2009 

Содержание SLIDE & LOCK SLA001-3







Отзывы: