VINYL WORKS CANADA CS Скачать руководство пользователя страница 6

# 10 - ATTACH LATCH & STRIKER 

Attach  striker  to  gate  using  two  (2)  #  10  x  1  inch  long  screws  provided.  The  gate  has  pre-drilled  holes  to      
accept the screws (Figure 10.1 & 10.2). Position the gate latch, with the striker in the catch (closed position), 
against the bottom right post and mark the four (4) screw locations (Figure 10.3). Pre-drill 1/8 inch holes and 
attach latch using four  (4) # 10 x 1  inch long screws provided. Do not over-tighten screws as the holes may 
strip. Make certain gate  functions properly. It should open  with tension, self-close and self-latch. If the gate 
does  not  function  properly  see  the  CORRECTIVE

CORRECTIVE

CORRECTIVE

CORRECTIVE  measure  /  3rd  hinge  instruction  packaged  within  the      

hardware pack. It will outline an additional procedure to correct / improve the function of the gate 

Figure 10.2 

Figure 10.1 

Figure 10.3 

# 11 - DETERMINE POOL DEPTH 

Figure 11.2 

Figure 11.1 

Measure  the  depth  of  the  pool  to          
determine if the FOOT EXTENSIONS are 
required  to  be  attached  to  your  pool 
step  entry  system.  Measure  the  inside 
depth  of  the  pool,  from  the  pool  floor  to 
the  top  of  the  top  rail  (Figure  11.1).  The 
CS  step  system  has  clearance  of  52.5 
inches  without  the  foot  extensions 
(Figure  11.2).  If  your  pool  measures 
equal  to  or  less  than  the  52  inches  the 
foot extensions are not required 

# 12 - ATTACH FOOT EXTENSIONS * (IF REQUIRED) * 

52" 

If  your  pool  depth,  from  pool 
floor to top of top rail, measures 
greater  than  52  inches  in 
height,  you  will  need  to  attach 
the  foot  extensions  provided. 
The foot extensions are used as 
shoes  for  the  bottom  of  the 
stringers  to  raise  the  height 
clearance of the CS step system 
over  your  pool  wall.  Fit  the  foot 
extensions  onto  the  bottom  of 
the  stringers  (Figure  12.1). 
Make  certain  to  fit  properly  - 
front  &  back  as  indicated  (front 
is  the  nose  of  the  stringer). 
Once  in  place,  pre-drill  a  3/16 
inch  pilot  hole  in  the  stringer 
and secure using a # 14 x 1 inch 
screw  both  front  &  back.  Make 
certain 

not 

to 

over-tighten 

screws. Repeat for all four 

#14 

Figure 12.1 

Front 

Back 

Measure 

Inside Pool 

Front 

Back 

Содержание CS









Отзывы: