manualshive.com logo in svg

Vinten Vision 10LF, Руководство по обслуживанию

Поделиться
Скачать
Vinten Vision 10LF Скачать руководство пользователя страница 31

31

Contents

Previous 

Page

First 

Page

Next 

Page

Previous 

View

11.5

Fill the tilt drag housing (1) with 16.25 cc of Vinten Fluid No. 3 (

Section 3

).

11.6

Install bearing (7) in outrigger (9).

11.7

Degrease and prime two screws (34) and one screw (6) with Loctite N primer and allow to dry.

11.8

Install `O' ring (5) in tilt bearing housing (33) and secure to outrigger (9) with two screws (34) and 

one screw (6) and Loctite 222E.

11.9

 Degrease and prime three screws (30) with Loctite N primer and allow to dry.

11.10 Install tilt brake plate (29) on outrigger (9) and secure with three screws (30) and Loctite 222E.

11.11 Align cutout in tilt drag cover/brake disc assembly (31) with tilt brake plate (29) and push the 
assembly onto the tilt bearing housing (33). Take care not to damage the omniseal (8).

11.12 Install `O' ring (5) and washer (4) in the tilt bearing housing (33).

11.13 Install drag shoe assembly (35) on the tilt bearing housing (33). Secure temporarily with two 
screws (36).

11.14 Install drag actuator shaft (3).

11.15 Install assembly in tilt centralizing fixture (

3390-905TL

).

11.16 Using the fixture, expand the drag shoe assembly.

11.17 Remove screws (36) one at a time and reinstall using Loctite 221 on threads and Loctite 601 
under heads. Torque-tighten screws to 7.34 Nm (65 lbf in.).

11.18 Remove from fixture.

11.19 Install `O' ring (32) in tilt drag cover/brake disc assembly (31).

11.20 Degrease and prime six screws (2) with Loctite N primer and allow to dry.

11.21 Install completed outrigger assembly on tilt drag housing (1). Align fixing holes and secure with 
six screws (2) and Loctite 222E.

11.22 Install pan brake pivot (13) in pan brake shoe assembly (12) and install in tilt mechanism.

11.23 The remaining tilt mechanism components are installed after assembly of the balance 
mechanism.

NOTE:

The design of the tilt brake cover/brake disc assembly changed from Serial No. 1197. 
Ensure correct housing and ‘O’ ring are replaced.

Содержание Vision 10LF






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды