Vinten 3395 Скачать руководство пользователя страница 22

Страница: 22 / 52

Brake knob adjustment

The pan and tilt brakes are set during manufacture so that, when the brakes are fully applied, the knob

is vertical. As the brakes bed in during use it may be necessary to reset the knobs to this position.

The procedure for resetting the pan and tilt brake knobs is as follows (

Fig 4.2

9.1

Prise out the centre of the appropriate brake knob

(5)

9.2

Turn the knob

(2)

clockwise to fully apply the brake.

9.3

Remove the screw

and washer

and pull the knob

off the shaft

9.4

Refit the knob on the shaft in the vertical position.

9.5

Turn the knob fully counter-clockwise and ensure the brake is released.

9.6

Turn the knob clockwise and ensure that the brake is fully applied when the knob is vertical.

Adjust the position of the knob if necessary.

9.7

Secure the knob with the screw

(3)

and washer

(4)

. Refit the knob centre

(4)

, using Silcoset 153.

Fig 4.2 Brake knob adjustment

(5)

(4)

(2)

(3)

(1)

Содержание 3395





















































Результаты поиска

Содержание 3395

Отзывы:

Бренды по названию

Популярные бренды

Vinten 3395, Руководство по обслуживанию

Результаты поиска

Содержание 3395

Отзывы:

Бренды по названию

Популярные бренды